To Adjust Steering Wheel Alignment

SERVICE AND ADJUSTMENTS

TOREPLACEMOTIONDRIVEBELT(SeeFig.20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt up- wards from transaxle pulley by deflecting belt keepers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 20

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral.

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT	NEUTRAL
LEVER	LOCK
	GATE
	ADJUSTMENT
	BOLT

FIG. 21

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL (See Fig. 22)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

	AXLE	RETAINING WASHERS
		RING
	COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

PXT16542 specifications

The Poulan PXT16542 is a robust and efficient lawn mower designed for homeowners seeking a reliable and powerful cutting tool for their gardens. Boasting a 42-inch cutting deck, this riding mower is perfectly suited for medium to large lawns, enabling efficient coverage and reduced mowing time.

One of the standout features of the PXT16542 is its powerful 16.5 HP Briggs & Stratton engine. This engine delivers optimized performance with substantial torque, ensuring seamless maneuverability and cutting power on various terrains. The integrated automatic transmission further enhances the mowing experience by allowing smooth speed adjustments, making it easy to navigate around obstacles and uneven surfaces.

A crucial technology in the PXT16542 is its cutting system, featuring a dual-blade design that provides a clean and precise cut every time. With multiple height adjustment settings, users can customize the cutting height to suit their lawn's needs, whether they prefer a close trim or a higher grass finish. This flexibility is essential for maintaining a healthy lawn and promoting robust growth.

The Poulan PXT16542 is also designed for user comfort and convenience. Its ergonomic seat ensures a comfortable riding experience, even during extended mowing sessions. Easy-to-reach controls make operation intuitive, while the easy-access fuel tank simplifies refueling. The inclusion of a tight turning radius allows for exceptional maneuverability, making it easy to navigate tight spots or flowerbeds without damaging the landscape.

Durability and maintenance are prioritized in this mower’s design. The rugged construction and high-quality materials used in the PXT16542 contribute to its longevity and reliability. Additionally, the mower comes with maintenance points conveniently located for easy access, allowing for quick checks and upkeep, which ultimately prolongs the life of the machine.

In summary, the Poulan PXT16542 is an ideal choice for homeowners needing a reliable, user-friendly riding mower. With its powerful engine, versatile cutting capabilities, user-centric design, and durable construction, this mower stands out as a dependable partner for lawn care, ensuring that your garden remains in pristine condition throughout the mowing season.