Poulan PP4620AVL Fueling & Lubrication, Starting, Fueling Engine, BAR and Chain Lubrication

Page 9

FUELING & LUBRICATION

WARNING: Remove fuel cap slow- ly when refueling.

FUELING ENGINE

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline. Included with this saw is a

3.2ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PROR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. Poulan or Poulan PROR oil resists high temperature thinning. If Poulan or Poulan PROR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15”--- 18” of rope per pull. Hold saw firmly while pulling starter rope.

Starter rope handle

Left hand on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the full extent (to the FULL CHOKE position).

3.Pull starter rope quickly with your right hand a maximum of 5 times. Then, pro- ceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents PP4620AVL Plan Ahead Starting ReminderMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlDo not cut more than one log at a time Elbow locked Thumb on underside of handlebarChain Brake and CKA Angle Kickback Safety FeaturesAssembly Computed kickback angle CKA TableAttaching the BAR & Chain If not Checking the tension Adjusting the tensionOperation Starting Fueling & LubricationFueling Engine BAR and Chain LubricationStarting a Warm Engine Cutting MethodsChain Brake Important PointsFelling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree VanceCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing Limbing and Pruning Important PointsPruning ErlyCleaning the air filter ServiceCleaning the Spark Arresting Screen AIR FilterStorage Need Service PART? Troubleshooting TableNeed ASSISTANCE? Trouble Cause RemedyLimited Warranty Ligations The U. S. EnvironmentalElectrolux Home PRODUCTS, INC NANCE, Replacement and Repair of Emission Related Parts Any

PP4620AVL specifications

The Poulan PP4620AVL is a powerful and versatile chainsaw designed for both homeowners and professionals who require a reliable tool for various cutting tasks. This model features a 46cc gas engine that delivers ample power to tackle a range of jobs, from light trimming to more demanding tree-felling applications.

One of the standout features of the Poulan PP4620AVL is its advanced air filtration system. This technology enhances engine durability and performance by ensuring that the engine is protected from dust and debris, prolonging its lifespan and maintaining optimal performance. The system is designed to be maintenance-free for a long duration, providing users with peace of mind during operation.

The PP4620AVL is equipped with a tool-free chain tensioning system, which allows for easy adjustments without the need for additional tools. This feature is particularly convenient for users who may need to make quick adjustments while working, ensuring minimal downtime. The chainsaw also has an automatic oiling system that lubricates the bar and chain during use, helping to reduce friction and wear for improved cutting efficiency.

Another impressive aspect of this chainsaw is its lightweight design. Weighing in at a manageable 11 pounds, the PP4620AVL is easy to handle for extended periods, reducing user fatigue while providing the necessary power to complete various tasks. The soft-grip handle adds comfort, allowing for improved control and maneuverability.

Safety is also a priority with the Poulan PP4620AVL. It features a chain brake system that stops the chain quickly in the event of kickback, providing an added layer of protection for the user. Additionally, the chainsaw is designed with an easy-to-access on/off switch and a throttle lockout, ensuring safe operation.

In terms of cutting power, the Poulan PP4620AVL comes with a 20-inch bar, making it suitable for cutting large logs and branches. The combination of the robust engine, efficient cutting system, and user-friendly features make this chainsaw a great choice for anyone from casual users to professionals seeking reliability and efficiency in their cutting tool. With the right maintenance, the PP4620AVL is sure to provide years of service for a wide range of cutting tasks.
Top Page Image Contents