Poulan PP4620AVL Cutting Methods, Starting a Warm Engine, Chain Brake, Important Points

Page 10

4.Push the choke/fast idle lever in to the HALF CHOKE position.

5.Pull the starter rope quickly with your right hand until the engine starts.

6.Allow the engine to run for approximately 30 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

ON/STOP SWITCH

CHOKE/FAST IDLE LEVER

FULL HALF OFF

(0.5 mm) thick. Repairs on a chain brake should be made by an authorized service deal- er. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON position.

2.Pull the choke/fast idle lever out to the HALF CHOKE position.

3.Pull the starter rope quickly with your right hand until the engine starts.

4.Squeeze and release the throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded if it has not started after 10 pulls.

Flooded engines can be cleared of excess fuel by following the warm engine starting proce- dure listed above. Ensure the ON/STOP switch is in the ON position.

Starting could require many pulls depending on how badly unit is flooded. If engine still fails to start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0.020″

Braking function control

CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this procedure. This is the only instance when the saw should be placed on the ground with the engine run- ning.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re-

place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PP4620AVL Starting Reminder Plan AheadHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackDo not cut more than one log at a time Maintain ControlReduce the Chance of Kickback Elbow locked Thumb on underside of handlebarKickback Safety Features Chain Brake and CKA AngleComputed kickback angle CKA Table AssemblyAttaching the BAR & Chain If not Adjusting the tension Checking the tensionOperation Fueling Engine Fueling & LubricationStarting BAR and Chain LubricationChain Brake Cutting MethodsStarting a Warm Engine Important PointsNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees VanceTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportPruning Limbing and Pruning Important PointsLimbing ErlyCleaning the Spark Arresting Screen ServiceCleaning the air filter AIR FilterStorage Need ASSISTANCE? Troubleshooting TableNeed Service PART? Trouble Cause RemedyLigations The U. S. Environmental Limited WarrantyElectrolux Home PRODUCTS, INC NANCE, Replacement and Repair of Emission Related Parts Any

PP4620AVL specifications

The Poulan PP4620AVL is a powerful and versatile chainsaw designed for both homeowners and professionals who require a reliable tool for various cutting tasks. This model features a 46cc gas engine that delivers ample power to tackle a range of jobs, from light trimming to more demanding tree-felling applications.

One of the standout features of the Poulan PP4620AVL is its advanced air filtration system. This technology enhances engine durability and performance by ensuring that the engine is protected from dust and debris, prolonging its lifespan and maintaining optimal performance. The system is designed to be maintenance-free for a long duration, providing users with peace of mind during operation.

The PP4620AVL is equipped with a tool-free chain tensioning system, which allows for easy adjustments without the need for additional tools. This feature is particularly convenient for users who may need to make quick adjustments while working, ensuring minimal downtime. The chainsaw also has an automatic oiling system that lubricates the bar and chain during use, helping to reduce friction and wear for improved cutting efficiency.

Another impressive aspect of this chainsaw is its lightweight design. Weighing in at a manageable 11 pounds, the PP4620AVL is easy to handle for extended periods, reducing user fatigue while providing the necessary power to complete various tasks. The soft-grip handle adds comfort, allowing for improved control and maneuverability.

Safety is also a priority with the Poulan PP4620AVL. It features a chain brake system that stops the chain quickly in the event of kickback, providing an added layer of protection for the user. Additionally, the chainsaw is designed with an easy-to-access on/off switch and a throttle lockout, ensuring safe operation.

In terms of cutting power, the Poulan PP4620AVL comes with a 20-inch bar, making it suitable for cutting large logs and branches. The combination of the robust engine, efficient cutting system, and user-friendly features make this chainsaw a great choice for anyone from casual users to professionals seeking reliability and efficiency in their cutting tool. With the right maintenance, the PP4620AVL is sure to provide years of service for a wide range of cutting tasks.
Top Page Image Contents