Poulan PPB3416, PPB4218 Throttle LOCK-OUT Chain Brake, CHOKE/FAST Idle Lever, Primer Bulb

Page 9

THROTTLE LOCK-OUT

CHAIN BRAKE

 

 

The THROTTLE LOCK--OUT must be

The chain brake is a device designed to stop

pressed before you can squeeze the throttle

the chain if kickback occurs. The chain brake

trigger. This feature prevents you from acci-

activates automatically in the event of kick-

dentally squeezing the trigger.

back. The chain brake activates manually if the

CHOKE/FAST IDLE LEVER

front hand guard is pushed forward. The chain

The choke and fast idle are set by pulling the

brake is disengaged by pulling the front hand

guard back toward the front handle as far as

CHOKE/FAST IDLE LEVER out to the full ex-

possible.

 

 

 

tent for cold starting or after refueling. The

 

 

 

 

 

 

 

choke provides additional fuel to the engine

CHAIN TENSION

 

 

during cold starting.

It is normal for a new chain to stretch during the

PRIMER BULB

first 15 minutes of operation. You should check

The PRIMER BULB circulates fuel to the car-

your chain tension frequently. See CHAIN

buretor to provide quicker starting.

TENSION under the ASSEMBLY section.

 

 

 

 

 

 

WARNING: Muffler is very hot during

In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a

and after use. Do not touch the muffler or al-

small amount (5 to 10%) of #1 Diesel Fuel or

low combustible material such as dry grass

kerosene.

Bar and chain oil must be free

or fuel to do so.

flowing for the oil system to pump enough oil

BEFORE STARTING ENGINE

for adequate lubrication. Genuine Poulan or

 

 

Poulan PRO bar and chain oil is recommended

WARNING: Be sure to read the fuel

to protect your unit against excessive wear

handling information in the safety rules sec-

from heat and friction. Poulan or Poulan PRO

oil resists high temperature thinning.

 

 

tion of this manual before you begin. If you do

 

 

If Poulan or Poulan PRO bar and chain oil is

not understand the fuel handling information

not available, use a good grade SAE 30 oil.

do not attempt to fuel your unit. Seek help

S Never use waste oil for bar and chain lubri-

from someone that does understand the in-

formation or call the customer assistance

cation.

 

 

 

help line at 1-800-554-6723.

S Always stop the engine before removing

FUELING ENGINE

the oil cap.

 

 

IMPORTANT

 

 

WARNING: Remove fuel cap slowly

 

 

Experience indicates that alcohol--blended

when refueling.

fuels (called gasohol or using ethanol or meth-

 

 

anol) can attract moisture which leads to sepa-

HELPFUL TIP

 

 

ration and formation of acids during storage.

To obtain the correct oil mix

 

Acidic gas can damage the fuel system of an

ratio, pour 3.2 ounces of

 

engine while in storage. To avoid engine prob-

2-cycle synthetic oil into

 

lems, the fuel system should be emptied before

one gallon of fresh gas.

 

storage for 30 days or longer. Drain the gas

This engine is certified to operate on unleaded

 

tank, start the engine and let it run until the fuel

gasoline. Before operation, gasoline must be

lines and carburetor are empty. Use fresh fuel

next season. See STORAGE section for addi-

mixed with a good quality synthetic 2-cycle air-

tional information.

 

 

cooled engine oil designed to be mixed at a ra-

 

 

tio of 40:1. Poulan/WEED EATER brand syn-

CHAIN BRAKE

 

 

thetic oil is recommended. A 40:1 ratio is

Ensure chain brake is disengaged by pulling

obtained by mixing 3.2 ounces (95 ml) of oil

the front hand guard back toward the front han-

with 1 gallon (4 liters) of unleaded gasoline.

dle as far as possible. The chain brake must be

Included with this saw is a 3.2 ounce (95 ml)

disengaged before cutting with the saw.

 

 

container of Poulan/WEED EATER brand syn-

WARNING: The chain must

 

 

thetic oil. Pour the entire contents of this con-

not

tainer into 1 gallon (4 liters) of gasoline to

move when the engine runs at idle speed. If

achieve the proper fuel mixture.

the chain moves at idle speed refer to CAR-

DO NOT USE automotive or marine oil.

BURETOR

ADJUSTMENT within

this

These oils will cause engine damage. When

manual. Avoid contact with the muffler. A hot

mixing fuel follow the instructions printed on

muffler can cause serious burns.

 

 

the container. Always read and follow the

 

 

 

 

safety rules listed under HANDLE FUEL

To stop the engine move the ON/STOP

WITH CAUTION.

switch to the STOP position.

 

 

BAR AND CHAIN LUBRICATION

 

 

 

 

The bar and chain require continuous lubri-

To start the engine hold the saw firmly on the

cation. Lubrication is provided by the auto-

ground as illustrated. Make sure the chain is

matic oiler system when the oil tank is kept

free to turn without contacting any object.

 

 

filled. Lack of oil will quickly ruin the bar and

 

 

 

 

chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Plan AheadTions found in this manual Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 If your hand slips off the front handlebarAttaching the BAR & Chain If not AssemblyAdjusting the tension Chain TensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW ON/STOPCHOKE/FAST Idle Lever Throttle LOCK-OUT Chain BrakePrimer Bulb Before Starting EngineStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingService Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Empty fuel tank and refill withLigations The U.S. Environmental Limited Warranty

PPB3416AV, PPB3416, PPB4218 specifications

The Poulan PPB3416, PPB4218, and PPB3416AV are versatile products designed to meet the needs of various landscaping and yard maintenance tasks. Each model provides users with reliable performance and innovative features that facilitate efficient operation, making them popular choices among homeowners and professionals alike.

The Poulan PPB3416 is known for its lightweight design and ease of use. This model features a 16-inch bar and chain, making it suitable for cutting small to medium-sized branches and shrubs. The powerful 33cc two-cycle engine delivers ample power for clean and precise cuts, ensuring users can accomplish their tasks without hassle. One of the standout features of the PPB3416 is its Easy Start system, which allows for quick and effortless starting, even after extended periods of inactivity. Additionally, the automatic chain oiler keeps the chain properly lubricated for smooth operation and increased longevity.

Moving to the Poulan PPB4218, this model takes efficiency up a notch with a larger 18-inch bar and chain, making it ideal for medium to large cutting jobs. The 40cc engine provides increased power, allowing users to tackle tougher jobs with ease. This chainsaw also incorporates an advanced anti-vibration system, which significantly reduces user fatigue during extended use. Its manageable weight ensures that users can operate it with comfort and control. Like the PPB3416, the PPB4218 features an automatic chain oiler and an Easy Start system, enhancing the overall user experience.

The Poulan PPB3416AV adds another layer of innovation with its advanced design and features. This model shares the compact 16-inch bar and 33cc engine with the PPB3416 but includes additional technology that enhances its performance. The AV designation stands for "Anti-Vibration," making the PPB3416AV ideal for users who prioritize comfort during prolonged usage. The improved ergonomic handle design offers a better grip, allowing for increased precision while reducing strain on the user's arms. This model also boasts tool-less chain tensioning, making adjustments quick and convenient.

In summary, the Poulan PPB3416, PPB4218, and PPB3416AV combine user-friendly features with powerful performance, making them effective tools for a variety of cutting tasks. With their innovative technologies and reliable build quality, these chainsaws are excellent choices for anyone looking to maintain their outdoor spaces efficiently. Whether you're a seasoned professional or a DIY enthusiast, Poulan's range of chainsaws provides the capability and convenience you need to get the job done.
Top Page Image Contents