Poulan PR1842STD owner manual Tractor

Page 16

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

TRAILING EDGE UP

BLADE

MANDREL ASSEMBLY

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

FLAT WASHER

LOCK WASHER

CENTER

HOLE

STAR

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with bal- ancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 12

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PR1842STD Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Hardware Steering Wheel SeatBlades KeysAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsCustomer Responsibilities General Recommendations Lubrication ChartBefore Each USE Tractor Engine Cleaning AIR Filter See FigMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model Number PR1842STDElectrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Decals Wheels and TiresOptional Equipment EngineSpark Arrester 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR1842STD specifications

The Poulan PR1842STD is a reliable riding lawn mower designed to meet the needs of residential users who require an efficient and powerful solution for lawn care. Its robust feature set and user-friendly design make it an ideal choice for homeowners with medium to large-sized lawns.

One of the defining characteristics of the PR1842STD is its powerful 18.5 HP Briggs & Stratton engine. This engine offers reliable starts and efficient operation, ensuring that users can tackle their mowing tasks with ease. The engine is paired with an automatic transmission, allowing for smooth speed adjustments without the need for constant gear shifting. This feature enhances user experience, making it more enjoyable and less cumbersome to operate.

The mower boasts a cutting deck width of 42 inches, which allows users to cover substantial ground in less time. The deck's design facilitates an adjustable cutting height ranging from 1 to 4 inches, giving users the flexibility to achieve their desired lawn appearance. This versatility is particularly beneficial for managing different grass types and growing conditions.

Another significant feature of the PR1842STD is its prominent turning radius. The mower can navigate tight spaces easily, which is a great asset for lawns with intricate landscaping. This capability ensures that users can maintain a neat appearance, even in corners and around obstacles.

In terms of comfort and convenience, the Poulan PR1842STD is equipped with a comfortable, high-back seat that provides support during extended mowing sessions. The ergonomics of the mower enhance user comfort, reducing fatigue as you tackle larger areas.

The mower also employs a reinforced frame and durable construction materials, ensuring longevity and resilience against the challenges of regular use. Maintenance is simplified through easy-access features, allowing users to perform routine checks and repairs without hassle.

In conclusion, the Poulan PR1842STD riding lawn mower combines power, flexibility, and user-centric design to deliver an exceptional mowing experience. With its reliable engine, adjustable cutting height, and comfortable seating, it is a standout choice for homeowners seeking efficiency in lawn care. Whether you're looking to maintain a pristine lawn or manage overgrown patches, the PR1842STD is equipped to handle the job with ease and reliability.
Top Page Image Contents