Poulan PR1842STD owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 29

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever to fast position.

•Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop. Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL (See Fig. 31)

The choke control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move choke control (located on dash panel) to full choke position.

•Loosen knob and remove cover assembly from air cleaner.

•Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

•Replace air cleaner cover assembly and tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

STOP

CLAMP

SWIVELSCREW

FIG. 30

CLAMP SCREW

FIG. 31

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PR1842STD II. Slope Operation Safety RulesIV. Service General OperationTable of Contents Customer Responsibilities Product SpecificationsKeys Unassembled HardwareSteering Wheel Seat BladesTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsBefore Each USE General Recommendations Lubrication ChartCustomer Responsibilities Tractor Engine Spark Plugs CleaningAIR Filter See Fig MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Tractor - Model Number PR1842STD SchematicElectrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Wheels and Tires DecalsSpark Arrester EngineOptional Equipment 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PR1842STD specifications

The Poulan PR1842STD is a reliable riding lawn mower designed to meet the needs of residential users who require an efficient and powerful solution for lawn care. Its robust feature set and user-friendly design make it an ideal choice for homeowners with medium to large-sized lawns.

One of the defining characteristics of the PR1842STD is its powerful 18.5 HP Briggs & Stratton engine. This engine offers reliable starts and efficient operation, ensuring that users can tackle their mowing tasks with ease. The engine is paired with an automatic transmission, allowing for smooth speed adjustments without the need for constant gear shifting. This feature enhances user experience, making it more enjoyable and less cumbersome to operate.

The mower boasts a cutting deck width of 42 inches, which allows users to cover substantial ground in less time. The deck's design facilitates an adjustable cutting height ranging from 1 to 4 inches, giving users the flexibility to achieve their desired lawn appearance. This versatility is particularly beneficial for managing different grass types and growing conditions.

Another significant feature of the PR1842STD is its prominent turning radius. The mower can navigate tight spaces easily, which is a great asset for lawns with intricate landscaping. This capability ensures that users can maintain a neat appearance, even in corners and around obstacles.

In terms of comfort and convenience, the Poulan PR1842STD is equipped with a comfortable, high-back seat that provides support during extended mowing sessions. The ergonomics of the mower enhance user comfort, reducing fatigue as you tackle larger areas.

The mower also employs a reinforced frame and durable construction materials, ensuring longevity and resilience against the challenges of regular use. Maintenance is simplified through easy-access features, allowing users to perform routine checks and repairs without hassle.

In conclusion, the Poulan PR1842STD riding lawn mower combines power, flexibility, and user-centric design to deliver an exceptional mowing experience. With its reliable engine, adjustable cutting height, and comfortable seating, it is a standout choice for homeowners seeking efficiency in lawn care. Whether you're looking to maintain a pristine lawn or manage overgrown patches, the PR1842STD is equipped to handle the job with ease and reliability.
Top Page Image Contents