Poulan PR1842STD owner manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 22

SERVICE AND ADJUSTMENTS

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 25)

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do not

lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub and

axle. Insert square key.

• Replace washers and snap retaining ring securely in

axle groove.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

• Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 25

TO START ENGINE WITH A WEAK BATTERY (See Fig. 26)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

FIG. 26

REPLACING BATTERY (See Figs. 27 and 28)

CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 27

TERMINAL

KEPS NUT

COVER

HEX

 

 

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

22

FIG. 28

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PR1842STD General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesBlades Unassembled HardwareSteering Wheel Seat KeysHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsCustomer Responsibilities General Recommendations Lubrication ChartBefore Each USE Tractor Engine Muffler CleaningAIR Filter See Fig Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model Number PR1842STDElectrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Decals Wheels and TiresOptional Equipment EngineSpark Arrester 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR1842STD specifications

The Poulan PR1842STD is a reliable riding lawn mower designed to meet the needs of residential users who require an efficient and powerful solution for lawn care. Its robust feature set and user-friendly design make it an ideal choice for homeowners with medium to large-sized lawns.

One of the defining characteristics of the PR1842STD is its powerful 18.5 HP Briggs & Stratton engine. This engine offers reliable starts and efficient operation, ensuring that users can tackle their mowing tasks with ease. The engine is paired with an automatic transmission, allowing for smooth speed adjustments without the need for constant gear shifting. This feature enhances user experience, making it more enjoyable and less cumbersome to operate.

The mower boasts a cutting deck width of 42 inches, which allows users to cover substantial ground in less time. The deck's design facilitates an adjustable cutting height ranging from 1 to 4 inches, giving users the flexibility to achieve their desired lawn appearance. This versatility is particularly beneficial for managing different grass types and growing conditions.

Another significant feature of the PR1842STD is its prominent turning radius. The mower can navigate tight spaces easily, which is a great asset for lawns with intricate landscaping. This capability ensures that users can maintain a neat appearance, even in corners and around obstacles.

In terms of comfort and convenience, the Poulan PR1842STD is equipped with a comfortable, high-back seat that provides support during extended mowing sessions. The ergonomics of the mower enhance user comfort, reducing fatigue as you tackle larger areas.

The mower also employs a reinforced frame and durable construction materials, ensuring longevity and resilience against the challenges of regular use. Maintenance is simplified through easy-access features, allowing users to perform routine checks and repairs without hassle.

In conclusion, the Poulan PR1842STD riding lawn mower combines power, flexibility, and user-centric design to deliver an exceptional mowing experience. With its reliable engine, adjustable cutting height, and comfortable seating, it is a standout choice for homeowners seeking efficiency in lawn care. Whether you're looking to maintain a pristine lawn or manage overgrown patches, the PR1842STD is equipped to handle the job with ease and reliability.
Top Page Image Contents