Poulan P4018WTL Starting a Warm Engine, Difficult Starting or starting a flooded engine

Page 10

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an authorized ser- vice dealer. Take your unit to the place of pur- chase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions 545137251 11/30/06Plan Ahead Starting ReminderTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Adjusting Screw Tensioning Rack AssemblyAttaching the BAR & Chain If not Chain Tension Adjusting the tensionAdjusting Screw Checking the tensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Braking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlFelling Large Trees Operating TipsTree Felling Techniques Notch CUT and Felling the TreeImportant Points Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing Limbing and Pruning Important PointsPruning Service Cleaning the Spark ARREST- ING Screen Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelStorage Other Load Adjustment EngineEngine Empty fuel tank and refill withLimited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair

P4018WTL specifications

The Poulan P4018WTL is a robust and reliable chainsaw designed for homeowners and outdoor enthusiasts alike. This powerful tool is engineered to tackle a variety of cutting tasks, from pruning branches to felling trees, making it an essential addition to any toolkit.

One of the standout features of the Poulan P4018WTL is its 40cc 2-cycle engine. This engine delivers strong power while maintaining a compact design, allowing for ease of use and maneuverability. With a maximum power output of 2.3 horsepower, this chainsaw ensures efficient cutting through even tougher materials. It is equipped with a 18-inch cut chain, providing a great balance of length and control for various cutting jobs.

The chainsaw utilizes an innovative Air Injection technology, which helps in keeping the air filter clean by utilizing centrifugal force to remove larger debris before they reach the filter. This means less maintenance and longer intervals between filter cleaning, allowing users to focus on their cutting tasks rather than upkeep.

The Poulan P4018WTL also features an automatic oiler system, ensuring that the chain and bar receive consistent lubrication during operation. This self-lubrication helps to minimize friction, promoting a longer lifespan for both the chain and the bar while enhancing cutting efficiency.

Safety is a key consideration in the design of the P4018WTL. The chainsaw is equipped with a chain brake that stops the chain immediately in the event of kickback, preventing accidents and ensuring safety during use. Additionally, the ergonomically designed handle provides a comfortable grip and reduces fatigue, making it easier to handle the chainsaw during extended use.

With a lightweight construction of approximately 10.6 pounds, the Poulan P4018WTL is easy to carry and maneuver, providing both power and portability. Furthermore, it is designed with reduced vibration technology, which minimizes user fatigue and enhances comfort during operation.

In conclusion, the Poulan P4018WTL chainsaw combines power, features, and safety to meet the demands of various cutting tasks. With its efficient engine, innovative technologies, and user-friendly design, it stands out as a reliable choice for both novice and experienced users looking to tackle their landscaping and woodcutting needs.
Top Page Image Contents