Poulan P4018WTL Chain Tension, Checking the tension, Adjusting the tension, Cutters

Page 7

4.Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket.

Bar bolts

Guide bar

5.Carefully remove the chain from the pack- age. Hold chain with the drive links as shown.

Tip of

Bar

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Cutters

Depth Gauge

Drive Links

6.Place chain over and behind clutch re- tainer, fitting the drive links in the clutch drum sprocket.

7.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

8.Fit chain drive links into bar groove.

9.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

10.Hold guide bar against the saw frame and install the clutch cover.

11.Replace the bar nuts and tighten finger tight. Once the chain is tensioned you will need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already installed)

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure the bar nuts are finger tight only. Attempting to tension the chain when the bar nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move chain around guide bar. If the chain does not rotate, it is too tight. If the chain is too loose, it will sag below the bar.

Guide

Bar

Chain Adjustment

Bar Nuts Adjusting Tool

Screw (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

An adjusting screw (located on the guide bar) is used to adjust the tension of the chain (see illustration).

1.Loosen bar nuts until they are finger tight against the clutch cover.

2.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Adjusting

Screw

3.Using bar tool, roll chain around guide bar to ensure all links are in bar groove.

4.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw until sag does not exist.

5.While lifting tip of guide bar, tighten bar nuts securely with the bar tool.

Bar Nuts

6.Use the screwdriver end of the bar tool to move chain around guide bar.

7.If chain does not rotate, it is too tight. Slightly loosen bar nuts and loosen chain by turning the adjusting screw. Retighten bar nuts.

8.If chain is too loose, it will sag below the guide bar. DO NOT operate the saw if the chain is loose.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 545137251 11/30/06 Manual de Instrucciones Manuel d’InstructionsPlan Ahead Starting ReminderTions found in this manual Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Reduce the Chance of KickbackMaintain Control Avoid Pinch-KickbackChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Adjusting Screw Tensioning Rack AssemblyAttaching the BAR & Chain If not Checking the tension Adjusting the tensionAdjusting Screw Chain TensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Inertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beNotch CUT and Felling the Tree Operating TipsTree Felling Techniques Felling Large TreesTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Important PointsLimbing Limbing and Pruning Important PointsPruning Service Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Cleaning the Spark ARREST- ING ScreenStorage Empty fuel tank and refill with Load Adjustment EngineEngine OtherLigations The U.S. Environmental Limited WarrantyNANCE, Replacement and Repair

P4018WTL specifications

The Poulan P4018WTL is a robust and reliable chainsaw designed for homeowners and outdoor enthusiasts alike. This powerful tool is engineered to tackle a variety of cutting tasks, from pruning branches to felling trees, making it an essential addition to any toolkit.

One of the standout features of the Poulan P4018WTL is its 40cc 2-cycle engine. This engine delivers strong power while maintaining a compact design, allowing for ease of use and maneuverability. With a maximum power output of 2.3 horsepower, this chainsaw ensures efficient cutting through even tougher materials. It is equipped with a 18-inch cut chain, providing a great balance of length and control for various cutting jobs.

The chainsaw utilizes an innovative Air Injection technology, which helps in keeping the air filter clean by utilizing centrifugal force to remove larger debris before they reach the filter. This means less maintenance and longer intervals between filter cleaning, allowing users to focus on their cutting tasks rather than upkeep.

The Poulan P4018WTL also features an automatic oiler system, ensuring that the chain and bar receive consistent lubrication during operation. This self-lubrication helps to minimize friction, promoting a longer lifespan for both the chain and the bar while enhancing cutting efficiency.

Safety is a key consideration in the design of the P4018WTL. The chainsaw is equipped with a chain brake that stops the chain immediately in the event of kickback, preventing accidents and ensuring safety during use. Additionally, the ergonomically designed handle provides a comfortable grip and reduces fatigue, making it easier to handle the chainsaw during extended use.

With a lightweight construction of approximately 10.6 pounds, the Poulan P4018WTL is easy to carry and maneuver, providing both power and portability. Furthermore, it is designed with reduced vibration technology, which minimizes user fatigue and enhances comfort during operation.

In conclusion, the Poulan P4018WTL chainsaw combines power, features, and safety to meet the demands of various cutting tasks. With its efficient engine, innovative technologies, and user-friendly design, it stands out as a reliable choice for both novice and experienced users looking to tackle their landscaping and woodcutting needs.
Top Page Image Contents