Poulan P4018WTL instruction manual Storage

Page 16

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY sec- tion.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual de Instrucciones Manuel d’Instructions 545137251 11/30/06Plan Ahead Starting ReminderTions found in this manual Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Adjusting Screw Tensioning Rack AssemblyAttaching the BAR & Chain If not Adjusting the tension Adjusting ScrewChain Tension Checking the tensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Starting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing Limbing and Pruning Important PointsPruning Service Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withLimited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair

P4018WTL specifications

The Poulan P4018WTL is a robust and reliable chainsaw designed for homeowners and outdoor enthusiasts alike. This powerful tool is engineered to tackle a variety of cutting tasks, from pruning branches to felling trees, making it an essential addition to any toolkit.

One of the standout features of the Poulan P4018WTL is its 40cc 2-cycle engine. This engine delivers strong power while maintaining a compact design, allowing for ease of use and maneuverability. With a maximum power output of 2.3 horsepower, this chainsaw ensures efficient cutting through even tougher materials. It is equipped with a 18-inch cut chain, providing a great balance of length and control for various cutting jobs.

The chainsaw utilizes an innovative Air Injection technology, which helps in keeping the air filter clean by utilizing centrifugal force to remove larger debris before they reach the filter. This means less maintenance and longer intervals between filter cleaning, allowing users to focus on their cutting tasks rather than upkeep.

The Poulan P4018WTL also features an automatic oiler system, ensuring that the chain and bar receive consistent lubrication during operation. This self-lubrication helps to minimize friction, promoting a longer lifespan for both the chain and the bar while enhancing cutting efficiency.

Safety is a key consideration in the design of the P4018WTL. The chainsaw is equipped with a chain brake that stops the chain immediately in the event of kickback, preventing accidents and ensuring safety during use. Additionally, the ergonomically designed handle provides a comfortable grip and reduces fatigue, making it easier to handle the chainsaw during extended use.

With a lightweight construction of approximately 10.6 pounds, the Poulan P4018WTL is easy to carry and maneuver, providing both power and portability. Furthermore, it is designed with reduced vibration technology, which minimizes user fatigue and enhances comfort during operation.

In conclusion, the Poulan P4018WTL chainsaw combines power, features, and safety to meet the demands of various cutting tasks. With its efficient engine, innovative technologies, and user-friendly design, it stands out as a reliable choice for both novice and experienced users looking to tackle their landscaping and woodcutting needs.
Top Page Image Contents