Poulan P4018AV, P4018WM, P3818AV, P3416, P3314WSA instruction manual Storage

Page 16

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY sec- tion.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/Weed Eater 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel sta- bilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 530165293-01 11/12/04Identification of Symbols Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Chain Brake and CKA Angle WE do not REPResent and YOU should not AS Sume That the Chain Brake willAssembly Attaching the BAR & Chain If notAdjusting the tension Adjusting ScrewChain Tension Checking the tensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Starting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning ING Without a SupportService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill with

P3314WSA, P3416, P3818AV, P4018AV, P4018WM specifications

Poulan Pro offers a wide array of reliable chainsaws designed to meet various user needs, and among their popular models are the P3314WSA, P3416, P4018WM, P3818AV, and P4018AV. Each of these models boasts unique features and technologies that cater to both professionals and hobbyists alike.

The Poulan P3314WSA is a lightweight chainsaw that weighs just 8.1 pounds, making it ideal for users who require portability without compromising power. It features a 33cc 2-cycle engine, delivering exceptional performance for cutting small to medium-sized trees and limbs. The 14-inch bar enables precise cuts, while the automatic oiler ensures continuous lubrication, prolonging the life of the chain.

Next up, the Poulan P3416 is designed for optimal performance with its 34cc engine and a longer 16-inch bar. This model excels at cutting larger branches and performing more demanding tasks. It features a convenient tool-less chain tensioning system, allowing for quick adjustments to ensure optimal cutting performance. Additionally, the anti-vibration technology enhances user comfort, reducing fatigue during extended use.

The P4018WM is a powerful chainsaw with a robust 40cc engine paired with an 18-inch bar, making it suitable for heavy-duty tasks like felling trees or tackling larger firewood jobs. The model includes a patented Easy Start technology, reducing the amount of pull force needed to start the engine. Furthermore, the adjustable chain oiler system enables users to customize oil flow based on cutting conditions.

The Poulan P3818AV, another standout model, is designed for versatility and ease of use. With an 38cc engine and an 18-inch bar, it provides a good balance of power and maneuverability. The advanced anti-vibration system significantly reduces user fatigue, making it perfect for long jobs. The chainsaw also includes an easy-access air filter that allows for simple maintenance while ensuring optimal engine performance.

Lastly, the P4018AV shares similar characteristics with the P4018WM but focuses on user convenience with its lightweight design and enhanced comfort features. It comes with an effective vibration dampening system and an easy-to-adjust chain tensioner, making it a practical choice for users looking to engage in prolonged cutting tasks without strain.

Overall, the chainsaws offered by Poulan Pro stand out not only for their powerful engines and innovative technologies but also for their user-friendly features, making them suitable for both casual users and professionals.
Top Page Image Contents