Poulan P3818AV, P4018WM, P3416 Chain Tension, Checking the tension, Adjusting the tension, Cutters

Page 7

Cutters

Depth Gauge

Drive Links

7.Place chain over and behind clutch re- tainer, fitting the drive links in the clutch drum sprocket.

8.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

9.Fit chain drive links into bar groove.

10.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

11.Now, install clutch cover making sure the adjusting pin is positioned in the low- er hole in the guide bar. Remember this pin moves the bar forward and back- ward as the screw is turned.

Clutch

Cover

Adjusting Pin Lower

Hole

Guide Bar

12.Install bar nuts and finger tighten only. Once the chain is tensioned, you will need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already installed)

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move chain around guide bar. If the chain does not rotate, it is too tight. If the chain is too loose, it will sag below the bar.

Guide

Bar

Chain Adjustmen

Bar Nuts Adjusting Tool

Screw (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

1.Loosen bar nuts until they are finger tight against the clutch cover.

2.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Adjusting

Screw

3.Using bar tool, roll chain around guide bar to ensure all links are in bar groove.

4.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw 1/4 turn clockwise. Repeat until sag does not exist.

Adjusting Screw -- 1/4 Turn

5.While lifting tip of guide bar, tighten bar nuts securely with the bar tool.

Bar Nuts

6.Use the screwdriver end of the bar tool to move chain around guide bar.

7.If chain does not rotate, it is too tight. Slightly loosen bar nuts and loosen chain by turning the adjusting screw 1/4 turn counterclockwise. Retighten bar nuts.

8.If chain is too loose, it will sag below the guide bar. DO NOT operate the saw if the chain is loose.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 11/12/04 530165293-01Plan Ahead Identification of SymbolsKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Sume That the Chain Brake will Chain Brake and CKA AngleWE do not REP Resent and YOU should not ASAttaching the BAR & Chain If not AssemblyChecking the tension Adjusting the tensionAdjusting Screw Chain TensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Inertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beNotch CUT and Felling the Tree Operating TipsTree Felling Techniques Felling Large TreesTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Important PointsING Without a Support Limbing and Pruning Important PointsLimbing PruningService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Cleaning the Spark ARREST- ING ScreenStorage Empty fuel tank and refill with Load Adjustment EngineEngine Other

P3314WSA, P3416, P3818AV, P4018AV, P4018WM specifications

Poulan Pro offers a wide array of reliable chainsaws designed to meet various user needs, and among their popular models are the P3314WSA, P3416, P4018WM, P3818AV, and P4018AV. Each of these models boasts unique features and technologies that cater to both professionals and hobbyists alike.

The Poulan P3314WSA is a lightweight chainsaw that weighs just 8.1 pounds, making it ideal for users who require portability without compromising power. It features a 33cc 2-cycle engine, delivering exceptional performance for cutting small to medium-sized trees and limbs. The 14-inch bar enables precise cuts, while the automatic oiler ensures continuous lubrication, prolonging the life of the chain.

Next up, the Poulan P3416 is designed for optimal performance with its 34cc engine and a longer 16-inch bar. This model excels at cutting larger branches and performing more demanding tasks. It features a convenient tool-less chain tensioning system, allowing for quick adjustments to ensure optimal cutting performance. Additionally, the anti-vibration technology enhances user comfort, reducing fatigue during extended use.

The P4018WM is a powerful chainsaw with a robust 40cc engine paired with an 18-inch bar, making it suitable for heavy-duty tasks like felling trees or tackling larger firewood jobs. The model includes a patented Easy Start technology, reducing the amount of pull force needed to start the engine. Furthermore, the adjustable chain oiler system enables users to customize oil flow based on cutting conditions.

The Poulan P3818AV, another standout model, is designed for versatility and ease of use. With an 38cc engine and an 18-inch bar, it provides a good balance of power and maneuverability. The advanced anti-vibration system significantly reduces user fatigue, making it perfect for long jobs. The chainsaw also includes an easy-access air filter that allows for simple maintenance while ensuring optimal engine performance.

Lastly, the P4018AV shares similar characteristics with the P4018WM but focuses on user convenience with its lightweight design and enhanced comfort features. It comes with an effective vibration dampening system and an easy-to-adjust chain tensioner, making it a practical choice for users looking to engage in prolonged cutting tasks without strain.

Overall, the chainsaws offered by Poulan Pro stand out not only for their powerful engines and innovative technologies but also for their user-friendly features, making them suitable for both casual users and professionals.
Top Page Image Contents