Poulan 952802048, 952802066 Throttle LOCK-OUT, CHOKE/FAST Idle Lever, Primer Bulb, Chain Brake

Page 9

THROTTLE LOCK-OUT

The THROTTLE LOCK--OUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from acci- dentally squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle are set by pulling the CHOKE/FAST IDLE LEVER out to the full ex- tent for cold starting or after refueling. The choke provides additional fuel to the engine during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the car- buretor to provide quicker starting.

CHAIN BRAKE

The chain brake is a device designed to stop the chain if kickback occurs. The chain brake

activates automatically in the event of kick- back. The chain brake activates manually if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front handle as far as possible.

CHAIN TENSION

It is normal for a new chain to stretch during the first 15 minutes of operation. You should check your chain tension each time before you start the chain saw. See CHAIN TENSION under the ASSEMBLY section.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury to the operator and/or damage the chain mak- ing it unusable.

BEFORE STARTING ENGINE

WARNING: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air- cooled engine oil designed to be mixed at a ra- tio of 40:1. Poulan/WEED EATER brand syn- thetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand syn- thetic oil. Pour the entire contents of this con- tainer into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under

HANDLE FUEL WITH CAUTION. CAUTION: Never use straight gasoline in your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or using ethanol or methanol) can cause major engine performance and durability problems.

WARNING: Alternative fuels (not gasoline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of al- ternative fuels will cause problems such as: im- proper clutch engagements, overheating, va- por lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan bar and chain oil is recom- mended to protect your unit against exces- sive wear from heat and friction. Poulan oil resists high temperature thinning.

If Poulan bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri- cation.

SAlways stop the engine before removing the oil cap.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

9

Image 9
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Plan AheadTions found in this manual Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InKickback Safety Features Chain Brake and CKA AngleChain saws as set by Ansi B175.1 Attaching the BAR & Chain If not AssemblyAdjusting the tension Chain TensionChecking the tension ON/STOP Switch Throttle Trigger OperationKnow Your Chain SAW CHOKE/FAST Idle Lever Throttle LOCK-OUTPrimer Bulb Chain BrakeStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points Use a wedge to remove pinched sawLimbing ServicePruning General RecommendationsClean AIR Filter Inspect and Clean Unit and DecalsCheck for Loose Fasteners and Parts Check Chain SharpnessChain Adjustment Cleaning the Spark ARREST- ING ScreenInspect Muffler and Spark Arresting Screen Replace Spark PlugIdle Speed-T Carburetor AdjustmentCooling System RightSeasonal Storage StorageFuel System EngineLoad Adjustment Engine Troubleshooting Table Cause RemedyLigations The U.S. Environmental Poulan