Poulan 115327926, P3816 Carburetor Adjustment, Cooling System, Seasonal Storage, Fuel System

Page 17

Hook Angle

 

0.025 inch

 

(0.65 mm)

 

Rounded

Right

Corner

 

Too Much Hook Angle

Squared Off

 

Corner

Wrong

WARNING: Maintain the proper hook angle according to the manufacturer’s specifi- cations for the chain you are using. Improper hook angle will increase the chance of kick- back which can result in serious injury.

4. Check and lower depth gauges.

Depth Gauge Tool

File

Depth Gauge

SPlace gauge tool on cutter.

SIf the depth gauge is higher than the depth gauge tool, file it level to the top of

the depth gauge tool.

SMaintain rounded front corner of depth gauge with a flat file.

NOTE: The very top of the depth gauge should be flat with the front

half rounded off with a flat file.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

COOLING SYSTEM

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

SAir intake on the starter S Air guide plate

S Fins on the flywheel

S Cooling fins on the cylinder

S Cylinder cover (directs cold air over the cylinder)

Clean the cooling system with a brush after each use, more often in demanding condi- tions. A dirty or blocked cooling system re- sults in the machine overheating which causes damage to the piston and cylinder.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp

object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

S Oil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual de Instrucciones Manuel d’Instructions Tions found in this manual Starting ReminderPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Ansi B175.1-2000 American National AssemblyAttaching the BAR & Chain If not Checking the tension Adjusting the tensionChain Tension Operation BAR and Chain Lubrication Before Starting Engine Fueling EngineFuel Requirements Starting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Kickback occursInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesCutting a Fallen Tree Notch CUT and Felling the TreeImportant Points Types of Cutting Used for BuckingBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingService Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelReplace Spark Plug Chain AdjustmentTo Sharpen Chain Replace Fuel FilterStorage Carburetor AdjustmentCooling System Seasonal StorageEngine Load Adjustment EngineOther Empty fuel tank and refill withLigations The U.S. Environmental Canada, contactPoulan

115327926, P3816, 966557801 specifications

The Poulan P3816 chainsaw, model number 966557801, is a robust and efficient tool designed to meet the needs of both novice users and seasoned professionals. Known for its cutting performance and user-friendly design, this chainsaw is ideal for various tasks, including pruning, tree felling, and firewood cutting.

One of the standout features of the Poulan P3816 is its powerful 38cc engine. This 2-cycle engine provides the necessary torque and speed to tackle tough cutting jobs efficiently. Additionally, it is designed with an easy-start system that minimizes the effort required to start the chainsaw, making it accessible for users of all skill levels. The engine also incorporates advanced technology to reduce emissions, making it environmentally friendly while still delivering impressive power.

The P3816 features a 16-inch bar with a low-profile chain, allowing for smoother cuts and reduced kickback, which enhances user safety. The chain is specially engineered for durability and longevity, ensuring that users can rely on it for recurring tasks without frequent replacements. Moreover, the chainsaw offers tool-less chain tensioning, allowing users to quickly adjust the chain without the need for additional tools, which contributes to operational efficiency.

Comfort is a critical consideration in the design of the Poulan P3816. It comes with an ergonomic handle that reduces vibrations during operation, providing a more comfortable grip for extended periods. The lightweight design, coupled with the well-balanced construction, allows for easier maneuverability and reduced fatigue.

In terms of maintenance, the chainsaw is equipped with an automatic oiling system that ensures consistent lubrication of the chain and bar. This feature helps prolong the life of the tool and enhances cutting performance. The transparent oil reservoir allows users to easily check the oil level, ensuring they are always prepared for their tasks.

In summary, the Poulan P3816, with model number 966557801, is engineered for versatility and ease of use. Its powerful engine, user-friendly features, and safety-oriented design make it an excellent choice for anyone in need of a reliable chainsaw. Whether you are a homeowner looking to maintain your property or a professional using it for daily jobs, the P3816 stands out as a dependable tool that combines performance with convenience.
Top Page Image Contents