Poulan BH 2160 Cutting a Fallen Tree, Types of Cutting Used for Bucking, Treat path

Page 12

SAs tree starts to fall, stop saw, put it down, and get away quickly on your planned re-

treat path.

SDO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

SCut shattered wood very carefully; sharp pieces of wood could be flung toward oper- ator.

SUse a sawhorse to cut small logs. Never allow another person to hold the log while cutting and never hold the log with your leg or foot.

SDo not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting

Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A SUPPORT

SOvercut through 1/3 of the diameter of the log.

SRoll the log over and finish with a second

overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR

SUPPORT STAND

SRemember your first cut is always on the compression side of the log.

(Refer to the illustrations below for your first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

Using a log for support

2nd Cut

1st Cut

1st Cut

2nd Cut

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents English Español Français Electrolux Home Products, Inc22/05 Identification of Symbols Safety RulesPlan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance of KickbackMaintain Control Chain Brake and CKA Angle Front Hand Guard, designed to reduceBack toward the operator BH2160 952044370Assembly Inside view Chain Brake Adjustment located on Chain BrakeAttaching the BAR & Chain If not Chain Brake NutsAdjusting the tension Checking the tensionChain Tension ON/STOP Switch Know Your Chain SAWThrottle Trigger Throttle LOCK-OUTStarting Fueling EngineBAR and Chain Lubrication Important Points to RememberCutting Methods Starting a Warm EngineImportant Points Tree Felling Techniques Felling Large Trees Notch CUT and Felling the TreeInches in diameter or larger FootingBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportService Limbing and Pruning Important PointsLimbing PruningCleaning the Spark ARREST- ING Screen Carburetor AdjustmentBAR Maintenance Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Ligations The U. S. Environmental Electrolux Home PRODUCTS, INCIntermediate 125 hours Extended 300 hours

BH 2160 specifications

The Poulan BH 2160 is a robust and reliable rear-tine tiller designed for both novice gardeners and seasoned horticulturists. With its powerful performance and user-friendly design, the BH 2160 has garnered a positive reputation among outdoor enthusiasts who require an efficient solution for cultivating soil.

At the heart of the Poulan BH 2160 is its potent 208cc four-stroke engine, which delivers ample power to tackle various soil types. The engine is designed for easy starting, ensuring that users can quickly get to work without the frustration of dealing with difficult pull starts. The tiller features a shift-on-the-go transmission with forward and reverse gears, allowing for enhanced maneuverability in tight spaces and making it easier to navigate around flower beds and garden plots.

One of the standout features of the BH 2160 is its robust tilling width. With the capability to till areas up to 16 inches wide, it allows users to cover more ground efficiently in less time. The heavy-duty steel tines dig deep into the soil, churning up stubborn dirt and turning hard ground into ready-to-plant soil. These tines are designed for durability and longevity, ensuring that they can withstand rigorous use over multiple seasons.

Ergonomics play a vital role in the design of the BH 2160, with an adjustable handle that can be tailored to different user heights. This feature promotes comfort during operation, reducing fatigue and enhancing control. The tiller also boasts a lightweight design, making it easier to manage while still providing the sturdy construction needed for tough tilling tasks.

In terms of safety, the Poulan BH 2160 comes equipped with user-friendly controls that are strategically located for easy access, allowing for quick adjustments while in operation. The tiller also features effective safety mechanisms, preventing accidental starts and ensuring that users can work with confidence.

In conclusion, the Poulan BH 2160 is an exceptional rear-tine tiller that expertly combines power, versatility, and ease of use. It is a worthy investment for anyone looking to cultivate their garden with efficiency and reliability. Whether preparing a small backyard garden or tilling larger plots, the BH 2160 provides the necessary power and features to get the job done effectively.
Top Page Image Contents