Poulan 966513901 instruction manual Important Points to Remember, Starting a Warm Engine

Page 10

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

WARNING: Do not attempt to throw or drop--start the chain saw. Doing so will put the operator at risk of serious injury due to loss of control of the chain saw.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Using the chain sawAlways use two hands when operating the chain saw Plan AheadHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackMaintain Control Kickback Safety FeaturesReduce the Chance of Kickback Avoid Pinch-KickbackChain saws as set by Ansi B175.1 Chain Brake and CKA AngleFront Hand Guard, designed to reduce Assembly Attaching the BAR & Chain If notAdjusting Screw Adjusting the tensionCutters Operation Before Starting Engine Fueling Engine Chain BrakeChain Tension Fuel RequirementsDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Right Foot Through Rear HandleOperating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingService Check Guide BAR Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelReplace Spark Plug Cleaning the Spark ARREST- ING ScreenChain Adjustment Chain SharpeningIdle Speed-T Carburetor AdjustmentStorage Cooling SystemEngine Load Adjustment EngineFuel System OtherPoulan PRO Charlotte, NC Canada, contactLigations The U.S. Environmental

966513901 specifications

The Poulan 966513901 is a powerful and versatile chainsaw designed for both professional landscapers and enthusiastic DIYers. Renowned for its durability and efficiency, this model is engineered to tackle a variety of cutting tasks, from felling trees to trimming branches and cutting firewood.

One of the standout features of the Poulan 966513901 is its robust engine. Powered by a high-performance gas engine, this chainsaw delivers impressive horsepower, enabling it to cut through tough materials with ease. The engine is also designed to provide efficient fuel consumption, which translates to longer operating times and reduced refueling intervals, making it ideal for extensive jobs.

The chainsaw features a 18-inch guide bar, optimizing cutting length while maintaining a manageable weight. This balance enhances maneuverability, allowing users to handle the chainsaw comfortably for extended periods. Additionally, the chainsaw comes equipped with a chain brake, a crucial safety feature that helps protect the user in the event of kickback. This brake engages automatically when the chainsaw is dropped or tilted unexpectedly, providing an additional layer of protection during operation.

Another noteworthy characteristic of the Poulan 966513901 is its Easy Start technology. This innovation simplifies the starting process, allowing users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms, making it accessible for users of varying experience levels.

The chainsaw also includes an adjustable automatic oiler, ensuring that the chain remains adequately lubricated during operation. This not only extends the lifespan of the chain but also enhances cutting efficiency. The oil reservoir is easy to access, enabling quick refills without interrupting work flow.

In terms of weight, the Poulan 966513901 strikes a balance between power and portability. It is lightweight enough for easy handling, yet robust enough to handle demanding tasks. This makes it a suitable choice for both professional and home use.

Overall, the Poulan 966513901 stands out in the crowded market of chainsaws due to its powerful performance, user-friendly features, and robust design. Whether you are cutting firewood, maintaining your property, or undertaking more significant landscaping projects, this chainsaw is a reliable companion that delivers efficiency and ease of use.
Top Page Image Contents