Poulan 966513901 Carburetor Adjustment, Idle Speed-T, Cooling System, Seasonal Storage

Page 17

All Cutters

Remove Damage

Same Length

 

 

Top Plate

 

Side Plate

SFile chain to meet the specifications as shown.

80˚60˚

30˚

Hook Angle

 

 

0.025 inch

 

 

(0.65 mm)

 

 

Rounded

Right

Corner

 

Too Much Hook Angle

 

Squared Off

 

 

Corner

Wrong

 

WARNING:

Maintain the proper

hook angle according to the manufacturer’s specifications for the chain you are using. Im- proper hook angle will increase the chance of kickback which can result in serious injury.

4. Check and lower depth gauges.

Depth Gauge Tool

File

Depth Gauge

SPlace gauge tool on cutter.

SIf the depth gauge is higher than the

depth gauge tool, file it level to the top of the depth gauge tool.

SMaintain rounded front corner of depth gauge with a flat file.

NOTE: The very top of the depth gauge should be flat with the front half rounded off with a flat file.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase

engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

COOLING SYSTEM

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

SAir intake on the starter S Air guide plate

S Fins on the flywheel

S Cooling fins on the cylinder

S Cylinder cover (directs cold air over the cylinder)

Clean the cooling system with a brush after each use, more often in demanding condi- tions. A dirty or blocked cooling system re- sults in the machine overheating which causes damage to the piston and cylinder.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place

and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more. If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

S Oil the chain and wrap it in heavy paper or cloth.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual de Instrucciones Manuel d’Instructions Always use two hands when operating the chain saw Using the chain sawStarting Reminder Plan AheadMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Avoid Pinch-KickbackFront Hand Guard, designed to reduce Chain Brake and CKA AngleChain saws as set by Ansi B175.1 Attaching the BAR & Chain If not AssemblyCutters Adjusting the tensionAdjusting Screw Operation Chain Tension Chain BrakeBefore Starting Engine Fueling Engine Fuel RequirementsStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingService Clean AIR Filter Inspect and Clean Unit and DecalsCheck Guide BAR Check Fuel Mixture LevelChain Adjustment Cleaning the Spark ARREST- ING ScreenReplace Spark Plug Chain SharpeningStorage Carburetor AdjustmentIdle Speed-T Cooling SystemFuel System Load Adjustment EngineEngine OtherLigations The U.S. Environmental Charlotte, NC Canada, contactPoulan PRO

966513901 specifications

The Poulan 966513901 is a powerful and versatile chainsaw designed for both professional landscapers and enthusiastic DIYers. Renowned for its durability and efficiency, this model is engineered to tackle a variety of cutting tasks, from felling trees to trimming branches and cutting firewood.

One of the standout features of the Poulan 966513901 is its robust engine. Powered by a high-performance gas engine, this chainsaw delivers impressive horsepower, enabling it to cut through tough materials with ease. The engine is also designed to provide efficient fuel consumption, which translates to longer operating times and reduced refueling intervals, making it ideal for extensive jobs.

The chainsaw features a 18-inch guide bar, optimizing cutting length while maintaining a manageable weight. This balance enhances maneuverability, allowing users to handle the chainsaw comfortably for extended periods. Additionally, the chainsaw comes equipped with a chain brake, a crucial safety feature that helps protect the user in the event of kickback. This brake engages automatically when the chainsaw is dropped or tilted unexpectedly, providing an additional layer of protection during operation.

Another noteworthy characteristic of the Poulan 966513901 is its Easy Start technology. This innovation simplifies the starting process, allowing users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms, making it accessible for users of varying experience levels.

The chainsaw also includes an adjustable automatic oiler, ensuring that the chain remains adequately lubricated during operation. This not only extends the lifespan of the chain but also enhances cutting efficiency. The oil reservoir is easy to access, enabling quick refills without interrupting work flow.

In terms of weight, the Poulan 966513901 strikes a balance between power and portability. It is lightweight enough for easy handling, yet robust enough to handle demanding tasks. This makes it a suitable choice for both professional and home use.

Overall, the Poulan 966513901 stands out in the crowded market of chainsaws due to its powerful performance, user-friendly features, and robust design. Whether you are cutting firewood, maintaining your property, or undertaking more significant landscaping projects, this chainsaw is a reliable companion that delivers efficiency and ease of use.
Top Page Image Contents