Poulan 545047515 instruction manual Storage

Page 16

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase

engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp

object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/Weed Eater 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel sta- bilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PP4218AVL 12/8/05Using the chain saw Always use two hands when operating the chain sawStarting Reminder Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackChain Brake and CKA Angle Kickback Safety FeaturesIf your hand slips off the front handlebar Adjusting Screw Tensioning Rack AssemblyAttaching the BAR & Chain If not Chain Tension Adjusting the tensionChecking the tension Operation Before Starting Engine Fueling Engine BAR and Chain LubricationImportant Points to Remember Cation Always stop the engine before removing the oil capStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing Limbing and Pruning Important PointsPruning Service Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withLimited Warranty Tions The U.S. Environmental ProtectionConsequential Damages Electro

545047515 specifications

The Poulan 545047515 is a powerful and efficient chainsaw designed for both professional and personal use. This model is particularly renowned for its robust performance, making it an excellent choice for those who require a reliable tool for cutting firewood, trimming trees, or tackling more demanding yard work.

One of the standout features of the Poulan 545047515 is its 50cc two-stroke engine, which delivers ample power and speed for various cutting tasks. This engine design ensures that users can handle larger jobs with ease, making it suitable for both occasional homeowners and seasoned professionals. The chainsaw is capable of achieving a high level of performance while also offering great fuel efficiency, which is a crucial aspect for anyone who plans to use it for extended periods.

Another significant characteristic of this model is its durability. Constructed with high-quality materials, the Poulan 545047515 is engineered to withstand daily wear and tear. The alloy components resist corrosion, ensuring that the chainsaw will last for many years if maintained properly. This durability is complemented by an easy-access air filter and a tool-less fuel cap, which simplify maintenance and refueling tasks.

Safety features are also a top priority with the Poulan 545047515. The chainsaw comes equipped with a chain brake, which instantly stops the chain in the event of a kickback, ensuring user safety. Additionally, the ergonomic design helps reduce vibrations during operation, providing a more comfortable handling experience while minimizing fatigue during long periods of use.

The Poulan 545047515 also includes advanced technologies such as the OxyPower engine technology, which enhances fuel efficiency and reduces emissions. This makes it an environmentally-friendly choice as it adheres to modern regulations on exhaust emissions.

In summary, the Poulan 545047515 chainsaw boasts a powerful 50cc engine, a focus on durability, essential safety features, and advanced technologies that promote fuel efficiency and lower emissions. It is designed to meet the needs of both casual users and professionals, ensuring that it remains a popular choice in the chainsaw market today. Whether you're cutting firewood or handling heavy-duty tasks, the Poulan 545047515 is equipped to deliver reliable performance and ease of use.
Top Page Image Contents