Poulan 545186756 instruction manual Service and Adjustments

Page 13

Adjusting Screw

5.Check the tension by lifting the chain from the guide bar. Remove some of the stiffness in the chain by pulling down and letting go of the chain sever- al times.

6.Continue turning the adjusting screw until the tension is correct (see step 4).

7.Tighten bar clamp nuts with a wrench.

8.Recheck chain tension.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious in- jury.

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull chain makes a sawdust powder and cuts slowly. See CHAIN SHARPENING in the SERVICE AND ADJUSTMENTS section.

CHECK GUIDE BAR

Conditions which require guide bar main- tenance:

SSaw cuts to one side or at an angle. S Saw has to be forced through the cut. S Inadequate supply of oil to the bar and

chain.

Check the condition of the guide bar each time the chain is sharpened. A worn guide bar will damage the chain and make cut- ting difficult.

After each use, with unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

S Disconnect the chain saw from the pow- er source.

S Loosen and remove bar clamp nuts. Remove bar and chain from saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to restore square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace the guide bar when the groove is worn, the guide bar is bent or crack--ed, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

LUBRICATION

Bar Oil Fill Cap

SCheck bar and chain oil before use and every 15 minutes while operating the saw. See GUIDE BAR AND CHAIN OIL un- der the OPERATION section.

INSPECT AND CLEAN UNIT AND LABELS

SAfter each use, inspect complete unit for

loose or damaged parts. Clean the unit and labels using a damp cloth with a mild detergent.

SWipe off the unit and labels with a clean dry cloth.

SERVICE AND ADJUSTMENTS

CHAIN SHARPENING

Chain sharpening requires special tools. You can purchase sharpening tools at an authorized service dealer or go to a pro- fessional chain sharpener.

WARNING: Avoid accidental start- ing. Always unplug saw from power source before installing a bar and/or chain.

CHAIN REPLACEMENT

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Español EnglishFrançais Operate Your SAW Safely Safety RulesPlan Ahead Sion and/or causing damage to unit Electrical SafetyUse a voltage supply as shown on the nameplate of the unit Conductor, such as metal fences or pipesReduce the Chance Kickback Guard Against KickbackMaintain Control Chain Brake and CKA Angle Kickback Safety FeaturesDouble Insulation Construction Either of these reactions may cause youOperation AssemblyChain Brake Before Starting SAW Guide BAR and Chain OILStopping Your SAW Starting Your SAWOperating Tips Cutting MethodsTree Felling Techniques Felling Large Trees 6 inches in diameter or largerCutting a Fallen Tree Bucking Hinge holds tree on stump and helps control fallImportant Points Bucking TechniquesLimbing Bucking Using a LOG or Support StandPruning Through the limbMaintenance Service and Adjustments Customer Serviceable Parts Chain AdjustmentTo Replace Chain Storage Troubleshooting Table Cause RemedySeasonal Storage Steps after each usePoulan PRO Warranty StatementTerry Fox Way Mississauga, Ontario L5V3E4

545186756 specifications

The Poulan 545186756 is a versatile chainsaw designed for both amateur woodworkers and seasoned professionals. Renowned for its reliability and robust performance, this chainsaw is crafted to handle a variety of cutting tasks ranging from trimming branches to felling small trees.

One of the standout features of the Poulan 545186756 is its powerful engine. Equipped with a 50cc, 2-stroke engine, this chainsaw delivers impressive cutting power. The engine is designed to provide optimal torque while maintaining fuel efficiency, which means users can work longer without frequent refueling. This perfect balance of power and efficiency makes it an ideal choice for homeowners and landscapers alike.

Furthermore, the Poulan 545186756 incorporates advanced technologies that enhance its usability. The chainsaw features an automatic oiling system, which ensures smooth chain operation and prolongs the life of the cutting equipment. This system automatically delivers oil to the chain as needed, reducing the maintenance required by the user. The tool-free chain tensioning system is another user-friendly feature, allowing for quick adjustments without the need for additional tools, enabling users to get back to work in minutes.

When it comes to safety, the Poulan 545186756 has multiple protective features. This includes a chain brake that quickly halts chain movement in the event of kickback, ensuring user safety during operation. The ergonomically designed handle provides a comfortable grip and minimizes vibrations, which can reduce operator fatigue during long cutting sessions.

The 18-inch bar length strikes a perfect balance between maneuverability and cutting capacity, allowing users to tackle various sizes of wood with precision. This chainsaw also features heavy-duty construction, making it durable enough to withstand the rigors of regular use.

In summary, the Poulan 545186756 is a powerful and reliable chainsaw equipped with advanced features that cater to both novice and experienced users. Its efficient engine, user-friendly technologies, and safety features make it a top choice for anyone looking to take on outdoor projects with confidence and ease.
Top Page Image Contents