Poulan 545137234 instruction manual Storage

Page 16

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase

engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp

object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual de Instrucciones Manuel d’Instructions 545137234 11/30/06Using the chain saw Always use two hands when operating the chain sawStarting Reminder Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackChain Brake and CKA Angle Kickback Safety FeaturesIf your hand slips off the front handlebar Adjusting Screw Tensioning Rack AssemblyAttaching the BAR & Chain If not Chain Tension Adjusting the tensionChecking the tension Operation Before Starting Engine Fueling Engine BAR and Chain LubricationImportant Points to Remember Cation Always stop the engine before removing the oil capStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing Limbing and Pruning Important PointsPruning Service Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withLimited Warranty Ligations The U.S. Environmental

545137234 specifications

The Poulan 545137234 is a powerful and efficient chainsaw designed for both professional and home use. This model is renowned for its robust performance and durability, making it an excellent choice for cutting firewood, clearing brush, and navigating more demanding woodcutting tasks. With a range of innovative features and cutting-edge technologies, the Poulan 545137234 stands out in the competitive landscape of chainsaws.

One of the main features of the Poulan 545137234 is its reliable engine. Powered by a potent 40cc 2-stroke engine, it delivers substantial power while maintaining efficiency. This engine is designed for superior performance, allowing users to tackle a variety of tasks with ease. Additionally, the engine is equipped with a primer bulb, which simplifies starting the chainsaw, ensuring users can get to work quickly.

The chainsaw features a 16-inch bar and chain, providing an optimal balance between cutting capacity and maneuverability. This size is perfect for cutting larger branches or logs while remaining lightweight and easy to handle, ideal for both novice and experienced operators. The chain itself is designed for smooth and fast cutting, enhancing productivity during operation.

Another standout characteristic of the Poulan 545137234 is its ergonomic design. The chainsaw includes comfort grips and a lightweight frame, which reduce operator fatigue during extended use. The adjustable chain tensioning system allows users to easily maintain the chain’s tightness, enhancing safety and efficiency.

Safety is paramount with the Poulan 545137234. It is equipped with a chain brake, which provides an extra layer of protection by stopping the chain’s movement in the event of a kickback. This feature is crucial in preventing injuries and ensuring a safer working environment.

In terms of technology, the Poulan 545137234 incorporates an advanced air filtration system that keeps the engine cleaner and helps extend its life. This technology is particularly beneficial when working in dusty environments, ensuring that the chainsaw maintains high performance levels over time.

Overall, the Poulan 545137234 combines power, efficiency, and safety features that cater to a wide range of users. Whether you are a seasoned professional or a weekend warrior tackling yard work, this chainsaw is equipped to handle the job with ease and reliability. Its thoughtful design and innovative technologies make it a commendable choice in the world of chainsaws.
Top Page Image Contents