Poulan 952802075 Carburetor Adjustments, Idle Speed-T, BAR Maintenance, Back View of Muffler

Page 15

Steel

Backplate

Muffler

Muffler

Bolts

Aluminum

Backplate Muffler

GasketBolt Cover Locknut

1.Loosen and remove the 3 cylinder cover screws. Remove the cylinder cover.

2.Pull off the spark plug boot.

3.Loosen and remove the locknut from the bolt cover. Remove the bolt cover.

4.Loosen and remove the 2 muffler bolts. Remove the muffler and backplates. No- tice the orientation of these parts for re- assembling.

5.Locate the 2 outlet cover screws on the muffler. Loosen and remove both screws. Remove the outlet cover and spark arresting screen.

BACK VIEW OF MUFFLER

Outlet Cover

Muffler

 

Screws

Spark Arresting

Screen

6.Clean the spark arresting screen with a wire brush. Replace screen if any wires are broken or screen is blocked after cleaning.

7.Reinstall spark arresting screen.

8.Reinstall outlet cover and 2 screws. En- sure outlet cover and both screws are re- installed correctly to prevent damage to the saw (see illustrations). The exhaust outlets must face the chain brake (bar side) of the saw.

Outlet Cover

Exhaust Outlets

Exhaust Outlets must face chain brake (bar side) of chain saw

9.Inspect the muffler gasket and replace if damaged.

10.Reinstall backplates, muffler gasket and muffler using muffler bolts. Tighten until secure.

11.Reinstall bolt cover and locknut.

12.Reinstall the spark plug boot.

13.Reinstall the cylinder cover and 3 screws. Tighten securely.

CARBURETOR ADJUSTMENTS

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow).

STurn idle speed screw (T) clockwise to in- crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call 1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi-

tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from

saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

15

Image 15
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Maintain ControlReduce the Chance of Kickback Avoid Pinch-KickbackChain Brake and CKA Angle Kickback Safety FeaturesAttaching the BAR & Chain If not AssemblyComputed kickback angle CKA Table Attaching the Bumper Spike If not already attachedTip Bar Adjusting the tensionAdjusting Screw Tensioning Rack Checking the tensionThrottle Trigger ON/STOP SwitchOperation Know Your SAWCHOKE/FAST Idle Lever Chain BrakeChain Tension To stop the engine move the ON/STOP Important Points to RememberStarting a Warm Engine Difficult Starting or starting a flooded engineImportant Points Cutting MethodsBraking function control Inertia activating function controlTypes of Cutting Used for Bucking Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsAIR Filter ServiceCleaning the Spark Arresting Screen PruningBack View of Muffler Carburetor AdjustmentsBAR Maintenance Idle Speed-TRight Chain SharpeningTools required To Sharpen ChainStorage Troubleshooting Table Cause Remedy Load Adjustment EngineEmpty fuel tank and refill with Ligations The U.S. Environmental Limited WarrantyCanada, contact Poulan PRONANCE, Replacement and Repair of Emission Related Parts Any

952802075 specifications

The Poulan 952802075 is a well-regarded, lightweight trimmer designed for both homeowners and professionals looking to maintain their lawns and gardens efficiently. One of its standout features is the 25cc 2-cycle gas engine, which provides ample power to tackle even the most challenging landscaping tasks. This engine is specifically designed for superior performance, delivering reliable starting and smooth operation, making it particularly user-friendly for those who may not be experienced with outdoor power equipment.

A key characteristic of the Poulan 952802075 is its versatility. It comes equipped with a detachable head that allows users to switch between various attachments, such as a string trimmer, hedge trimmer, and blower, catering to different gardening needs. This versatility is further enhanced by the inclusion of a dual-line bump head, which ensures efficient cutting and reduces the amount of time spent trimming grass and weeds.

Ergonomics play a considerable role in the design of the Poulan 952802075. The trimmer features a straight shaft, which allows for better reach under bushes or around flower beds, promoting more efficient trimming in tight spaces. Additionally, the easy-grip handle provides comfort during prolonged use, minimizing fatigue for the operator.

Poulan’s commitment to innovation is evident in the incorporation of advanced technologies into the 952802075 model. The trimmer features a simplified starting system, which reduces the effort required to start the engine, making it more accessible for all users. Furthermore, the design includes features aimed at reducing vibration, which not only enhances user comfort but also leads to extended operating periods without discomfort.

Another notable characteristic of the Poulan 952802075 is its lightweight construction, making it easy to maneuver without sacrificing durability. Despite its lightweight nature, the trimmer is built to withstand the rigors of outdoor work, ensuring longevity and reliability.

In summary, the Poulan 952802075 combines power, versatility, and user-friendly features in a well-designed package, making it an excellent choice for anyone looking to maintain their outdoor spaces efficiently. Its advanced technology, ergonomic aspects, and lightweight build set it apart as a leading option in the outdoor power equipment market. This trimmer ultimately serves as a dependable tool for achieving a well-kept yard with minimal hassle.