Poulan 952802075 instruction manual Storage

Page 17

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

NOTE: This spark ignition system complies with the Canadian standard ICES--002.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten with a 3/4 inch socket wrench. Tighten securely. Spark plug gap should be 0.025 inches.

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws Tighten securely.

Spark Plug Boot

COOLING SYSTEM

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

SAir intake on the starter S Air guide plate

S Fins on the flywheel

S Cooling fins on the cylinder

S Cylinder cover (directs cold air over the cylinder)

Clean the cooling system with a brush after each use, more often in demanding condi- tions. A dirty or blocked cooling system re- sults in the machine overheating which causes damage to the piston and cylinder.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp

object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

S Oil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distrib-

ute oil.

SReplace spark plug with new one of rec-

ommended type and heat range.

SClean air filter.

SCheck entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesComputed kickback angle CKA Table AssemblyAttaching the Bumper Spike If not already attached Attaching the BAR & Chain If notAdjusting Screw Tensioning Rack Adjusting the tensionChecking the tension Tip BarOperation ON/STOP SwitchKnow Your SAW Throttle TriggerChain Tension CHOKE/FAST Idle LeverChain Brake Starting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine To stop the engine move the ON/STOPBraking function control Cutting MethodsInertia activating function control Important PointsNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Types of Cutting Used for BuckingBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingCleaning the Spark Arresting Screen ServicePruning AIR FilterBAR Maintenance Carburetor AdjustmentsIdle Speed-T Back View of MufflerTools required Chain SharpeningTo Sharpen Chain RightStorage Empty fuel tank and refill with Troubleshooting Table Cause RemedyLoad Adjustment Engine Canada, contact Limited WarrantyPoulan PRO Ligations The U.S. EnvironmentalNANCE, Replacement and Repair of Emission Related Parts Any

952802075 specifications

The Poulan 952802075 is a well-regarded, lightweight trimmer designed for both homeowners and professionals looking to maintain their lawns and gardens efficiently. One of its standout features is the 25cc 2-cycle gas engine, which provides ample power to tackle even the most challenging landscaping tasks. This engine is specifically designed for superior performance, delivering reliable starting and smooth operation, making it particularly user-friendly for those who may not be experienced with outdoor power equipment.

A key characteristic of the Poulan 952802075 is its versatility. It comes equipped with a detachable head that allows users to switch between various attachments, such as a string trimmer, hedge trimmer, and blower, catering to different gardening needs. This versatility is further enhanced by the inclusion of a dual-line bump head, which ensures efficient cutting and reduces the amount of time spent trimming grass and weeds.

Ergonomics play a considerable role in the design of the Poulan 952802075. The trimmer features a straight shaft, which allows for better reach under bushes or around flower beds, promoting more efficient trimming in tight spaces. Additionally, the easy-grip handle provides comfort during prolonged use, minimizing fatigue for the operator.

Poulan’s commitment to innovation is evident in the incorporation of advanced technologies into the 952802075 model. The trimmer features a simplified starting system, which reduces the effort required to start the engine, making it more accessible for all users. Furthermore, the design includes features aimed at reducing vibration, which not only enhances user comfort but also leads to extended operating periods without discomfort.

Another notable characteristic of the Poulan 952802075 is its lightweight construction, making it easy to maneuver without sacrificing durability. Despite its lightweight nature, the trimmer is built to withstand the rigors of outdoor work, ensuring longevity and reliability.

In summary, the Poulan 952802075 combines power, versatility, and user-friendly features in a well-designed package, making it an excellent choice for anyone looking to maintain their outdoor spaces efficiently. Its advanced technology, ergonomic aspects, and lightweight build set it apart as a leading option in the outdoor power equipment market. This trimmer ultimately serves as a dependable tool for achieving a well-kept yard with minimal hassle.
Top Page Image Contents