Poulan 545123644 Carburetor Adjustment, BAR Maintenance, Chain Sharpening, Ignition Timing

Page 15

11.Reinstall backplate, outlet guide, muffler gasket, and muffler using muffler bolts. Tighten until secure.

12.Reinstall bolt cover and locknut. Tighten securely.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle speed screw (T) clockwise to in-

crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your

authorized

service

dealer

or

call

1--800--554--6723.

 

 

 

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi- tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from

saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

SBurring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat

file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and dis- card.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0.6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

Cylinder

Spark

Cover

 

Plug Boot

 

Spark

 

Plug

 

STORAGE

 

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.

SBefore storing, drain all fuel from the unit. Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric

motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents English Español Français545123644 Plan Ahead Identification of SymbolsSafety Rules Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionMaintain Control Reduce the Chance of KickbackKickback Path Avoid Obstructions Clear Working Area Back toward the operator Kickback Safety FeaturesChain Brake and CKA Angle Guide bar up and back toward the operatorLength AssemblyAdjusting Screw Tensioning Rack Computed kickback angle CKA TableAdjusting the tension Checking the tensionMount the Bar Throttle Lockout ON/STOP SwitchKnow Your SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationCutting Methods Starting a Warm EngineImportant Points Tree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Bucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen AIR FilterIgnition Timing Carburetor AdjustmentBAR Maintenance Chain SharpeningNeed ASSISTANCE? Limited WarrantyNeed Service PART? Need ASSISTANCE?Tions The U.S. Environmental Protection Your Warranty Rights and ObligaIntermediate 125 hours Extended 300 hours

545123644 specifications

The Poulan 545123644 is a powerful chainsaw designed to meet the needs of homeowners and light commercial users. Known for its reliability and ease of use, this chainsaw has become a popular choice for those looking to tackle various cutting tasks efficiently. With a focus on performance, the Poulan 545123644 features a robust engine that delivers exceptional power. Equipped with a 50cc two-stroke gasoline engine, it offers a balance of torque and RPM, making it ideal for felling trees, limb removal, and cutting firewood.

One of the standout features of the Poulan 545123644 is its lightweight design, which enhances maneuverability and reduces operator fatigue during extended use. Weighing in at just over 11 pounds, it allows users to manage their cutting tasks with ease. The chainsaw also incorporates an ergonomic handle that ensures a comfortable grip, promoting better control while operating.

The chainsaw's 20-inch bar length provides ample reach for cutting larger logs and branches without excessive effort. It also comes equipped with a low-kickback chain, which enhances safety by minimizing the risk of kickback incidents—a common concern for chainsaw users. This feature is particularly important for both novice and experienced operators.

To further enhance performance, the Poulan 545123644 utilizes advanced technologies such as an automatic oiling system, ensuring the chain receives the lubrication it needs for smooth operation. This not only prolongs the lifespan of the chain but also reduces maintenance, allowing users to focus on their cutting tasks.

Another noteworthy aspect of the Poulan chainsaw is its easy-start mechanism, which utilizes a spring-assisted pull starter. This innovation significantly reduces the effort required to start the engine, making it user-friendly, particularly for those who may struggle with traditional starting methods.

In terms of durability, the Poulan 545123644 features a rugged construction that withstands the rigors of regular use, ensuring longevity. Its air filtration system also helps to extend engine life by keeping dust and debris out of the engine.

Overall, the Poulan 545123644 combines power, safety, and ease of use, making it an excellent choice for those looking to tackle outdoor projects with confidence. Whether you are pruning trees or preparing firewood for winter, this chainsaw delivers reliability and performance, ensuring that you can complete your tasks efficiently.
Top Page Image Contents