Poulan 176038 owner manual Before Starting the Engine, To Operate on Hills, To Transport

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 6)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

•Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE

WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

17/32 WASHER

3/8 WASHER

 

SHOULDER

GAUGE WHEEL

BOLT

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

"ENGAGED" POSITION

ATTACHMENT LIFT

LEVER HIGH POSITION

LOW

POSITION

ATTACHMENT

DISCHARGE

CLUTCH LEVER

"DISENGAGED"

GUARD

POSITION

FIG. 7

12

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the dis- charge guard in place.

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 12)

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model NO. PO14542B Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig ¿ Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen See Fig To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigPreliminary Setting Final SettingStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO14542BElectrical 2122175158 175566175141 Chassis and Enclosures 155924X012 Drive 117 110 111 115174973 154407 Bellcrank Clutch173898 Steering Assembly KEY Part NO. NO. Description Engine 170551 14831517060620 Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck 171977 165898174284 Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill

176038 specifications

The Poulan 176038 is a high-performance gas-powered chainsaw designed for both home and professional use. Known for its powerful engine and reliable performance, this model has become popular among landscapers, farmers, and DIY enthusiasts alike. One of the standout features of the Poulan 176038 is its robust 38cc engine, which provides adequate power for a variety of cutting tasks, from trimming branches to felling trees. The chainsaw is equipped with a 16-inch bar and chain, allowing for efficient cutting while maintaining a lightweight design.

One significant technology integrated into the Poulan 176038 is the easy-start mechanism, which simplifies the starting process, reducing the effort needed to get the saw running. This feature is especially useful for beginners or those who may find traditional pull-start mechanisms challenging. Additionally, the Chainsaw has an adjustable fuel and oil mixture, allowing users to customize performance based on their specific needs and the type of job at hand.

Safety is a priority with the Poulan 176038, and it includes several features to protect the user. The chainsaw is equipped with a chain brake that quickly stops the chain rotation in case of kickback, reducing the risk of injury. Moreover, it features a tensioning system for quick adjustments to the chain without the need for additional tools, enhancing both usability and safety.

Another remarkable characteristic of this chainsaw is its lightweight design, weighing around 10 pounds, which makes it easy to handle for extended periods without causing fatigue. This portability is advantageous for users who need to perform extensive cutting tasks in various locations.

The Poulan 176038 also boasts an anti-vibration system, making operation smoother and more comfortable. This system helps to minimize operator fatigue, allowing users to work longer without discomfort. Overall, the Poulan 176038 stands out as an efficient, user-friendly chainsaw that balances power, safety, and convenience, making it an excellent choice for both casual users and professionals seeking to tackle various cutting tasks with ease. Whether you are maintaining your garden or handling more significant woodcutting jobs, the Poulan 176038 delivers in performance and reliability.
Top Page Image Contents