Poulan 176038 owner manual To Replace Headlight Bulb, Interlocks and Relays, Replacing Battery See

Page 22

SERVICE AND ADJUSTMENTS

POSITIVE TERMINAL

 

NEGATIVE TERMINAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHASSIS

 

 

CABLES

POSITIVE

NEGATIVE

TERMINAL

TERMINAL

CHARGED

 

BATTERY

FIG. 25

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

KEPS

NUT

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

REPLACING BATTERY (See Fig. 26 AND 27)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position and open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

•Close battery box door.

SEAT PAN

BATTERY

BOX DOOR

FIG. 26

22

 

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 28

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. PO14542B Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesSteering Wheel Seat Unassembled PartsKeys To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsADD Gasoline Mowing TipsTo Start Engine See Fig General Recommendations ¿ Lubrication ChartCustomer Responsibilities Before Each USETires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR Screen See FigTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery SeeTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysPreliminary Setting To Adjust Throttle Control Cable See FigTo Adjust Carburetor See Fig Final SettingFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO14542BElectrical 2122175566 175158175141 Chassis and Enclosures 155924X012 Drive 117 110 111 115154407 Bellcrank Clutch 174973173898 Steering Assembly KEY Part NO. NO. Description Engine 148315 17055117060620 Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck 165898 171977174284 Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill

176038 specifications

The Poulan 176038 is a high-performance gas-powered chainsaw designed for both home and professional use. Known for its powerful engine and reliable performance, this model has become popular among landscapers, farmers, and DIY enthusiasts alike. One of the standout features of the Poulan 176038 is its robust 38cc engine, which provides adequate power for a variety of cutting tasks, from trimming branches to felling trees. The chainsaw is equipped with a 16-inch bar and chain, allowing for efficient cutting while maintaining a lightweight design.

One significant technology integrated into the Poulan 176038 is the easy-start mechanism, which simplifies the starting process, reducing the effort needed to get the saw running. This feature is especially useful for beginners or those who may find traditional pull-start mechanisms challenging. Additionally, the Chainsaw has an adjustable fuel and oil mixture, allowing users to customize performance based on their specific needs and the type of job at hand.

Safety is a priority with the Poulan 176038, and it includes several features to protect the user. The chainsaw is equipped with a chain brake that quickly stops the chain rotation in case of kickback, reducing the risk of injury. Moreover, it features a tensioning system for quick adjustments to the chain without the need for additional tools, enhancing both usability and safety.

Another remarkable characteristic of this chainsaw is its lightweight design, weighing around 10 pounds, which makes it easy to handle for extended periods without causing fatigue. This portability is advantageous for users who need to perform extensive cutting tasks in various locations.

The Poulan 176038 also boasts an anti-vibration system, making operation smoother and more comfortable. This system helps to minimize operator fatigue, allowing users to work longer without discomfort. Overall, the Poulan 176038 stands out as an efficient, user-friendly chainsaw that balances power, safety, and convenience, making it an excellent choice for both casual users and professionals seeking to tackle various cutting tasks with ease. Whether you are maintaining your garden or handling more significant woodcutting jobs, the Poulan 176038 delivers in performance and reliability.
Top Page Image Contents