Poulan 530087823 Braking function control, Inertia activating function control, Important Points

Page 9

tip in the danger zone with any hard object. Kickback can also be caused by pinching the saw chain along the top of the guide bar. This action may push the guide bar rapidly back toward the operator. Either of these events may cause you to lose control of the saw which could result in serious injury or even death. DO NOT RELY UPON ANY OF THE SAFETY DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Reduced--kickback guide bars and low--kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kick- back chain and bar as original equipment. If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be re- placed by an authorized service dealer if any part is worn to less than 1/32” thick. Repairs on a chain brake should be made by an au- thorized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Hold the han- dles with both hands and apply full throttle. Activate the chain brake by turning your left wrist against the hand guard without releas- ing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Hold the chain saw approximately 14” (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and

after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re-

place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and thus increase the possibility of kick-

back.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and al- low the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the en- tire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or engine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting load, un- necessary wear can occur to the chain, bar, and engine.

S To avoid losing control when cut is

complete, do not put pressure on saw at end of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc.

SCarefully plan your sawing operation in ad-

vance.

SClear the work area. You need a clear area all around the tree so you can have secure footing.

S Study the natural conditions that can cause the tree to fall in a particular direc- tion.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents WCI Outdoor Products, Inc 295Plan Ahead Clothing Gloves Safety Sa fety Chaps ShoesOperate Your SAW Safely Never try to start the saw when the guide bar is in a cutMaintain Your SAW in Good Working Order Handle Fuel with CautionMaintain Control Kickback Safety FeaturesReduce the Chance Kickback Always begin cutting with the engine at fullBar Chain Brake and CKA AngleComputed kickback angle CKA Table Safety Notice Exposure toFueling Engine Adjusting the tensionBAR and Chain Lubrication Never use waste oil for bar and chain lubri- cationStarting a Warm Engine Important Points to RememberChain Brake Right foot through rear handleInertia activating function control Braking function controlImportant Points Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Plan a clear retreat pathTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandBucking Without a Support Limbing and PruningImportant Points Cleaning the air filterLimbing PruningStorage Troubleshooting Table Spark PlugLigations The U. S. Environmental Contact your retailerRepair or Replacement of Parts

530087823 specifications

The Poulan 530087823 is a powerful and versatile chainsaw, well-regarded for its reliability and ease of use. Designed for both professional landscapers and homeowners, this model stands out with its user-friendly features and robust performance, making it an ideal tool for a variety of cutting tasks.

One of the key features of the Poulan 530087823 is its 18-inch cutting bar, which allows for efficient cutting of larger logs and branches. This ample size strikes a balance between maneuverability and cutting capability, making it suitable for both trimming and heavier jobs. The chainsaw is powered by a dependable gas engine, which delivers the power necessary to tackle tough tasks with ease.

Equipped with advanced technologies, this model benefits from a patented air filtration system that ensures cleaner air intake, extending the life of the engine. This feature minimizes maintenance by reducing the frequency of filter changes, allowing users to focus on their work rather than upkeep. Additionally, the Poulan 530087823 incorporates an anti-vibration system that enhances the comfort of use; it reduces fatigue during extended cutting sessions, leading to improved accuracy and safety.

User convenience is emphasized by the chainsaw's tool-less chain adjustment system, which enables quick and hassle-free adjustments to the chain tension without the need for additional tools. This feature is particularly valuable during outdoor use, where convenience and efficiency are paramount. Moreover, the chainsaw features a primer bulb for easy starting, reducing the effort required to fire up the engine.

The Poulan 530087823 also comes with a safety chain brake, which is a critical feature in preventing accidents during operation. This brake system engages quickly in the event of kickback, stopping the chain immediately and enhancing user safety.

Overall, the Poulan 530087823 stands out due to its combination of powerful performance, user-friendly features, and a strong emphasis on safety. With its durable construction and advanced technologies, this chainsaw is a reliable choice for both casual users and professionals, capable of handling a wide range of cutting tasks effectively. Whether trimming branches or felling small trees, the Poulan 530087823 provides the performance and innovation needed to get the job done.
Top Page Image Contents