Poulan 350 Tree Felling Techniques, Felling Large Trees, Notch CUT and Felling the Tree

Page 11

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain

and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unneces- sary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for lon- ger than 30 seconds at full throttle.

S To avoid losing control when cut is com- plete, do not put pressure on saw at end of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified immediately.

SCarefully plan your sawing operation in ad- vance.

Make sure there is enough room for the tree to fall. Maintain a distance of 2-1/2tree lengths from the nearest person or other objects. En- gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta- ples, and wire from the tree where cuts are to be made.

Plan a clear retreat path to the rear and diag- onal to the line of fall.

Plan a clear retreat path

Direction of Fall

45_

FELLING LARGE TREES

(6 inches (15 cm) in diameter or larger) The notch method is used to fell large trees. A notch is cut on the side of the tree in the de- sired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend to fall into the notch.

NOTE: If the tree has large buttress roots, remove them before making the notch. If us- ing saw to remove buttress roots, keep saw chain from contacting ground to prevent dull- ing of the chain.

NOTCH CUT AND FELLING THE TREE

SMake notch cut by cutting the top of the notch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut remove the notch of wood from the tree.

Final (felling) cut here, 2 inches (5 cm) above center of notch.

SClear the work area. You need a clear area all around the tree so you can have secure

footing.

SThe chain saw operator should keep on the uphill side of the terrain as the tree is

likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause

the tree to fall in a particular direction. Natural conditions that can cause a tree to fall in a particular direction include:

SThe wind direction and speed.

S The lean of the tree. The lean of a tree

First cut

Notch

Second cut

Hinge

might not be apparent due to uneven or sloping terrain. Use a plumb or level to de- termine the direction of tree lean.

SWeight and branches on one side. S Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it can snap and fall toward the operator. Check for broken or dead branches which can fall on you while cutting.

S After removing the wood from the notch, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches (5 cm) higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. This hinge will help prevent the tree from falling in the wrong direction.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents English Español Français Manual de Instrucciones Manuel d’InstructionsPlan Ahead Identification of SymbolsSafety Rules Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionMaintain Control Kickback Safety FeaturesReduce the Chance of Kickback Sume That the Chain Brake will Chain Brake and CKA AngleWE do not REP Resent and YOU should not ASChain Brake Nuts AssemblyInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Throttle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationImportant Points Cutting MethodsStarting a Warm Engine Direction of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen AIR FilterIgnition Timing Carburetor AdjustmentBAR Maintenance Chain SharpeningNeed ASSISTANCE? Need Service PART?Need ASSISTANCE? StorageElectrolux Home PRODUCTS, INC Limited WarrantyTions The U.S. Environmental Protection Placement and Repair of Emission

530164364, 350 specifications

The Poulan 350,530164364 is a remarkable chainsaw that has made its mark as a reliable tool for both professionals and homeowners. Designed for versatility and ease of use, this chainsaw features a robust engine that delivers consistent power for a variety of cutting tasks.

One of the standout features of the Poulan 350 is its potent 2-stroke engine, which offers a balance of power and efficiency. With a displacement of around 50cc, this chainsaw can handle larger cutting jobs, making it suitable for everything from pruning trees to felling medium-sized ones. The engine is designed to provide high torque at low RPMs, ensuring that users can tackle tough wood without excessive strain on the machine or themselves.

In addition to its powerful engine, the Poulan 350 incorporates advanced technologies that enhance its usability. The chainsaw features an automatic oiling system that lubricates the bar and chain continuously, minimizing wear and ensuring smooth operation. This system is particularly useful during prolonged use, as it helps maintain the cutting performance and prolongs the life of the chain.

Comfort is another key characteristic of the Poulan 350,530164364. The chainsaw is designed with an ergonomic handle that reduces vibrations, allowing users to operate the tool comfortably for extended periods. Additionally, the lightweight construction of the equipment makes it easy to maneuver, reducing fatigue during demanding tasks.

Safety is a priority with this model, which includes several features aimed at protecting the user. The chainsaw is equipped with a chain brake that activates instantly if kickback occurs, stopping the chain's movement to reduce the risk of injury. Moreover, the Poulan 350 comes with a throttle lock that ensures the chainsaw operates only when intended.

Maintenance is simplified with the Poulan 350,530164364, as it features a tool-less access system for the air filter and spark plug. This design allows for quick and hassle-free servicing of the chainsaw, ensuring that it remains in optimal working condition.

In summary, the Poulan 350,530164364 combines power, innovation, and user-friendly features, making it an ideal choice for those looking to tackle a variety of cutting jobs effectively and safely. Whether you're a seasoned professional or a DIY enthusiast, this chainsaw is designed to deliver performance and reliability.
Top Page Image Contents