Poulan 530088788 operating instructions Safety Notice Exposure to, Back toward the operator

Page 5

Kickback can also be caused by pinching the saw chain along the top of the guide bar. This action may push the guide bar rapidly back toward the operator. Either of these events may cause you to lose control of the saw which could result in serious injury or even death. DO NOT RELY UPON ANY OF THE SAFETY DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Reduced--kickback guide bars and low--kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kick- back chain and bar as original equipment. Repairs on a chain brake should be made by an authorized servicing dealer. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest au- thorized master service dealer.

S Tip contact in some cases may cause a lightning fast reverse REACTION, kicking guide bar up and back toward operator.

SPinching the saw chain along the top of the guide bar may push the guide bar rapidly

back toward the operator.

SEither of these reactions may cause you to lose control of the saw which could result in serious injury. Do not rely exclusively upon safety devices built into your saw.

NOTE: If this saw is to be used for commer- cial logging, a chain brake is required and shall not be removed or otherwise disabled to comply with Federal OSHA Regulations for Commercial Logging. Contact your Au- thorized Service Dealer or call 1--800--554--6423.

SAFETY NOTICE: Exposure to

vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE: Your saw is equipped with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require many internal combustion engines to be equipped with a spark arresting screen by law. If you operate a chain saw in a state or locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to

5

do so is a violation of the law. Refer to the SERVICE section for maintenance of the spark arresting screen.

STANDARDS: This saw is listed by Un- derwriter’s Laboratories, Inc., in accordance with American National Standards for Gaso- line--Powered Chain Saw Safety Require- ments (ANSI B175.1-1991).

Failure to follow all Safety Rules and Precau- tions can result in serious injury. If situations occur which are not covered in this manual, use care and good judgement. If you need assistance, contact your Authorized Service Dealer.

Protective gloves (not provided) should be worn during assembly.

ATTACHING THE BAR & CHAIN (If not

already attached)

WARNING: If received assembled, repeat all steps to ensure your saw is proper- ly assembled and all fasteners are secure. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving!

SLoosen and remove the chain brake nuts

and the chain brake from the saw.

S Remove the plastic shipping spacer (if present).

Shipping

Spacer

Assembly

 

Tool

Chain Brake

 

Chain Brake Nuts

SAn adjusting pin and screw is used to ad- just the tension of the chain. It is very im- portant when assembling the bar, that the pin located on the adjusting screw aligns into a hole in the bar. Turning the screw will move the adjustment pin up and down the screw. Locate this adjustment before you begin mounting the bar onto the saw. See illustration below.

Adjustment

Screw

S Turn the adjusting screw counterclock- wise to move the adjusting pin almost as

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 3450 Operate Your SAW Safely Plan AheadMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance Kickback KickbackMaintain Control Ened after tensioning the chainElbow locked Thumb on underside of handlebar Kickback Safety FeaturesChain Brake Back toward the operator Safety Notice Exposure toChecking the tension Know Your SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine ON/STOP SwitchBAR and Chain Lubrication Important Points to RememberImportant Points Starting a Warm EngineFelling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree NecessaryCutting a Fallen Tree Bucking Using a LOG or SUP- Port StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points PruningLimbing AIR FilterCleaning the Spark ARREST- ING Screen BAR MaintenanceCarburetor Adjustments Inspect Muffler and Spark Arresting ScreenMotors or switches, furnaces, etc Troubleshooting Table Cause RemedyStorage CallLigations The U. S. Environmental Electrolux Home Products North AMERICA, Division of WCI Out

530088788 specifications

The Poulan 530088788 is a versatile and robust chainsaw designed to deliver reliable performance for both novice users and seasoned professionals. Known for its durability and efficiency, this chainsaw has become a popular choice among homeowners and landscapers alike.

One of the standout features of the Poulan 530088788 is its powerful engine. The chainsaw is equipped with a potent 50cc two-stroke engine that provides ample power for cutting through a variety of woods. This engine strikes a balance between efficiency and output, ensuring that users can tackle larger cutting tasks without experiencing excessive fatigue.

In terms of design, the Poulan 530088788 is built for comfort. It comes with an ergonomic handle that reduces vibration during operation, allowing for extended periods of use without discomfort. The adjustable chain tensioning system is another notable feature, enabling users to make quick adjustments to the chain without the need for additional tools, enhancing the overall user experience.

Safety is a paramount consideration with chainsaws, and the Poulan 530088788 incorporates multiple safety features. It features a chain brake that can be easily activated in case of kickback, providing peace of mind to users. The chainsaw also includes a safety throttle lock that prevents accidental starts, ensuring that the user has control at all times.

In terms of technologies, the Poulan 530088788 utilizes an advanced air filtration system that helps extend the life of the equipment. This feature reduces the amount of dust and debris that can enter the engine, leading to improved performance and longevity. Moreover, the chainsaw is designed for easy starting, courtesy of its spring-assisted starting system, which minimizes the effort required to get the engine running.

Additionally, the Poulan 530088788 comes with a 20-inch guide bar. This length allows for cutting larger logs while maintaining precision. The inclusion of a high-performance chain further enhances cutting efficiency, enabling users to quickly and effectively tackle their tasks.

In conclusion, the Poulan 530088788 is a feature-rich chainsaw that offers a perfect combination of power, safety, and ease of use. Whether you are trimming branches, felling trees, or tackling firewood, this chainsaw has the capabilities to get the job done efficiently and effectively. Its thoughtful design and reliable performance make it a worthy investment for anyone in need of a dependable cutting tool.
Top Page Image Contents