Poulan 530163654 Fueling Engine, BAR and Chain Lubrication, Important Points to Remember

Page 9

WARNING: Remove fuel cap slow- ly when refueling.

FUELING ENGINE

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PROR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. Poulan or Poulan PROR oil resists high temperature thinning. If Poulan or Poulan PROR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

S Always stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

9

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15”---18” of rope per pull. Hold saw firmly while pulling starter rope

Starter rope handle

Left hand

on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or warm engine after running out of fuel):

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

1.Move ON/STOP switch to the ON posi- tion.

2.Pull out choke/fast idle to the full extent.

3.Slowly press primer bulb 6 times.

4.Pull the starter rope quickly with your right hand 5 times Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in com- pletely (to the OFF position).

6.Pull the starter rope quickly with your right hand until the engine starts.

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

Image 9
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance Kickback Kickback Safety FeaturesMaintain Control Your left arm straight with the elbow lockedComputed kickback angle CKA Table Chain Brake and CKA AngleFront Hand Guard, designed to reduce Back toward the operatorAttaching the BAR & Chain If not Tip BarCutters Depth Gauge Drive Links Adjusting the tension Chain Tension Including units with chain already installedChecking the tension Know Your SAW ON/STOP SwitchThrottle Trigger Throttle LockoutBAR and Chain Lubrication Fueling EngineImportant Points to Remember Right foot through rear handleDifficult Starting or starting a flooded engine Starting a Warm EngineBraking function control Caution The chain brake must be Inertia activating function controlTree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points PruningLimbing AIR FilterCarburetor Adjustment Cleaning the air filterBAR Maintenance Inspect Muffler and Spark Arresting ScreenChain Sharpening Need Service PART?Ignition Timing Spark PlugTroubleshooting Table Cause Remedy Ligations The U. S. Environmental Your Warranty Rights and OB

530163654 specifications

The Poulan 530163654 is a versatile and reliable chainsaw that caters to the needs of both homeowners and professionals. This chainsaw is designed to deliver powerful performance while being user-friendly, making it an ideal choice for a variety of cutting tasks such as tree felling, limb trimming, and firewood preparation.

One of the standout features of the Poulan 530163654 is its robust engine. Equipped with a potent two-stroke engine, the chainsaw provides impressive cutting power, allowing users to tackle tougher jobs with ease. The engine's design ensures higher efficiency and lower emissions, which is essential for environmentally conscious users. This focus on green technology reduces the overall carbon footprint while maintaining superior performance.

Another notable aspect of the Poulan 530163654 is its lightweight design. Weighing in at just about 10 pounds, the chainsaw is easy to maneuver, even for extended periods. This aspect is particularly beneficial for homeowners and casual users who may not be accustomed to handling heavier power tools. The chainsaw also features an ergonomically designed handle, ensuring a comfortable grip and reducing user fatigue during prolonged use.

The Poulan 530163654 comes equipped with a 16-inch guide bar, which strikes a perfect balance between cutting capacity and ease of handling. This size is particularly advantageous for various landscaping tasks, as it allows users to quickly make precise cuts without being cumbersome or difficult to control. Additionally, the chainsaw utilizes a low-kickback chain, enhancing safety and providing a smoother cutting experience.

This model also includes advanced safety features such as a chain brake and hand guard, which help to prevent accidental injuries. The durable construction of the chainsaw ensures it can withstand regular use in demanding environments, contributing to its longevity and reliability.

Overall, the Poulan 530163654 is a powerful, lightweight, and efficient chainsaw that meets the needs of a wide range of users. Whether you're a seasoned professional or a weekend warrior, this chainsaw offers the ideal combination of power, safety, and ease of use, making it a worthy investment for any outdoor enthusiast.