Poulan 545001484 instruction manual Service, Limbing and Pruning Important Points, AIR Filter

Page 13

Using a support stand

2nd Cut

1st Cut

1st Cut

2nd Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or ob- jects at the nose of the guide bar when limb- ing or pruning. Allowing such contact can re- sult in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, platforms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure foot- ing and balance.

SWatch out for springpoles. Springpoles are small size limbs which can catch the saw chain and whip toward you or pull you off bal-

ance. Use extreme caution when cutting small size limbs or slender material.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

SKeep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop- erly.

S Leave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and

limbs. Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

SRemove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your first cut 1/3 of the way

through the bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch collar from the truck of the tree.

Second cut

Third cut

Collar

First cut

Pruning technique

SERVICE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . Before each use For damaged parts . . Before each use For loose caps . . . . . . Before each use For loose fasteners . . . Before each use For loose parts . . . . . . Before each use

Inspect and Clean:

Bar . . . . . . . . . . . . . . . . Before each use Complete saw . . . . . . . After each use Air filter . . . . . . . . . . . . . Every 5 hours* Chain brake . . . . . . . . Every 5 hours* Spark arresting screen

and muffler . . . . . . . . . Every 25 hours* Replace spark plug . Yearly Replace fuel filter . . . Yearly

* Hours of Operation

AIR FILTER

CAUTION: Do not clean filter in gasoline or other flammable solvent to avoid creating a fire hazard or producing harmful evapora- tive emissions.

Cleaning the air filter:

A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean after 15 tanks of fuel or 5 hours of operation, which- ever comes first. Clean more frequently in

13

Image 13
Contents Electrolux Home Products, Inc English Español Français22/05 Safety Rules Identification of SymbolsPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Front Hand Guard, designed to reduce Chain Brake and CKA AngleBack toward the operator BH2160 952044370Inside view Chain Brake Adjustment located on Chain Brake AssemblyAttaching the BAR & Chain If not Chain Brake NutsChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine StartingBAR and Chain Lubrication Important Points to RememberStarting a Warm Engine Cutting MethodsImportant Points Notch CUT and Felling the Tree Tree Felling Techniques Felling Large TreesInches in diameter or larger FootingCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points ServiceLimbing PruningCarburetor Adjustment Cleaning the Spark ARREST- ING ScreenBAR Maintenance Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Load Adjustment Engine Limited WarrantyEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Ligations The U. S. EnvironmentalIntermediate 125 hours Extended 300 hours

545001484 specifications

The Poulan 545001484 is a powerful and efficient chainsaw designed for both professional and home use. Renowned for its robust performance, this model is ideal for pruning, cutting firewood, and tackling various outdoor projects. The chainsaw boasts a lightweight construction, enabling users to operate it for extended periods without experiencing excessive fatigue.

One of the standout features of the Poulan 545001484 is its reliable 50cc two-cycle engine. This high-performance engine provides ample power to cut through thick branches and logs, ensuring efficiency in various cutting tasks. The chainsaw's air injection system is another noteworthy technology that enhances its performance by keeping the air filter cleaner for longer, reducing downtime for maintenance. This means users can focus on their work, knowing they won’t have to clean or replace the filter frequently.

The design of the Poulan 545001484 incorporates a 18-inch bar and chain, striking a balance between agility and the ability to tackle larger cuts. This length allows for smooth cutting while still being manageable for users of various skill levels. Additionally, the chainsaw features an automatic oiler, ensuring that the bar and chain are properly lubricated during operation, which extends the life of both components and promotes cutting efficiency.

Safety is paramount in chainsaw design, and the Poulan 545001484 does not compromise in this area. It comes equipped with features such as a chain brake, which stops the chain immediately in case of kickback, enhancing user protection. The cushioned, ergonomic handle aids in reducing vibrations during use, further increasing comfort and control for the operator.

Easy maintenance is another appealing aspect of the Poulan 545001484. The tool-less chain tensioning system allows users to adjust the chain quickly and easily without needing additional tools, which is particularly beneficial during long cutting sessions. Overall, the Poulan 545001484 combines power, efficiency, and user-friendly design, making it a preferred option for anyone in need of a reliable and versatile chainsaw for various outdoor tasks. Its innovative features cater to experienced users while remaining accessible for novices, ensuring it stands out in a competitive market.