Poulan 545001484 instruction manual Starting, Fueling Engine, BAR and Chain Lubrication

Page 9

FUELING & LUBRICATION

WARNING: Remove fuel cap slowly when refueling.

FUELING ENGINE

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce contain- er of oil. Pour the entire contents of this con- tainer into 1 gallon of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thorough- ly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine PoulanR bar and chain oil is recom- mended to protect your unit against exces- sive wear from heat and friction. PoulanR oil resists high temperature thinning. If Pou- lanR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15”--18” of rope per pull.

Hold saw firmly while pulling starter rope.

Starter rope handle

Left hand

on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

NOTE: Do not attempt to cut material with the fast idle lock button in the locked position.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

ON/STOP SWITCH

(SIDE VIEW)

ON

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull choke knob out to the full extent.

3.Slowly press primer bulb 6 times.

4.Squeeze and hold throttle trigger. With thumb press fast idle lock down; then re- lease throttle trigger.

Fast idle lock button

Throttle lock--out

Throttle

Choke knob

 

trigger

 

5.Sharply pull the starter rope handle 5 times with your right hand. Then, pro- ceed to the next step.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents English Español Français Electrolux Home Products, Inc22/05 Identification of Symbols Safety RulesPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance of KickbackMaintain Control Front Hand Guard, designed to reduce Chain Brake and CKA AngleBack toward the operator BH2160 952044370Inside view Chain Brake Adjustment located on Chain Brake AssemblyAttaching the BAR & Chain If not Chain Brake NutsAdjusting the tension Checking the tensionChain Tension Know Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine StartingBAR and Chain Lubrication Important Points to RememberCutting Methods Starting a Warm EngineImportant Points Notch CUT and Felling the Tree Tree Felling Techniques Felling Large TreesInches in diameter or larger FootingCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points ServiceLimbing PruningCarburetor Adjustment Cleaning the Spark ARREST- ING ScreenBAR Maintenance Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Ligations The U. S. EnvironmentalIntermediate 125 hours Extended 300 hours

545001484 specifications

The Poulan 545001484 is a powerful and efficient chainsaw designed for both professional and home use. Renowned for its robust performance, this model is ideal for pruning, cutting firewood, and tackling various outdoor projects. The chainsaw boasts a lightweight construction, enabling users to operate it for extended periods without experiencing excessive fatigue.

One of the standout features of the Poulan 545001484 is its reliable 50cc two-cycle engine. This high-performance engine provides ample power to cut through thick branches and logs, ensuring efficiency in various cutting tasks. The chainsaw's air injection system is another noteworthy technology that enhances its performance by keeping the air filter cleaner for longer, reducing downtime for maintenance. This means users can focus on their work, knowing they won’t have to clean or replace the filter frequently.

The design of the Poulan 545001484 incorporates a 18-inch bar and chain, striking a balance between agility and the ability to tackle larger cuts. This length allows for smooth cutting while still being manageable for users of various skill levels. Additionally, the chainsaw features an automatic oiler, ensuring that the bar and chain are properly lubricated during operation, which extends the life of both components and promotes cutting efficiency.

Safety is paramount in chainsaw design, and the Poulan 545001484 does not compromise in this area. It comes equipped with features such as a chain brake, which stops the chain immediately in case of kickback, enhancing user protection. The cushioned, ergonomic handle aids in reducing vibrations during use, further increasing comfort and control for the operator.

Easy maintenance is another appealing aspect of the Poulan 545001484. The tool-less chain tensioning system allows users to adjust the chain quickly and easily without needing additional tools, which is particularly beneficial during long cutting sessions. Overall, the Poulan 545001484 combines power, efficiency, and user-friendly design, making it a preferred option for anyone in need of a reliable and versatile chainsaw for various outdoor tasks. Its innovative features cater to experienced users while remaining accessible for novices, ensuring it stands out in a competitive market.
Top Page Image Contents