Poulan 530165399 instruction manual Storage

Page 16

6.Reinstall spark arresting screen, exhaust outlet cover, and nut. Tighten nut securely.

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY sec- tion.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place

and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage.

SStore in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/Weed Eater 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel sta- bilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 530165399 12/8/05Plan Ahead Starting ReminderTions found in this manual Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InKickback Safety Features Chain Brake and CKA AngleChain saws as set by Ansi B175.1 If your hand slips off the front handlebarAssembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension ON/STOP Switch Throttle Trigger OperationKnow Your Chain SAW ON/STOPThrottle LOCK-OUT Chain Brake CHOKE/FAST Idle LeverPrimer Bulb Before Starting EngineImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Right Foot Through Rear HandleBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Important PointsBucking Using a LOG or Support Stand Bucking Without a SupportLimbing and Pruning Important Points LimbingService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withTions The U.S. Environmental Protection Electrolux Home PRODUCTS, INCConsequential Damages Electro

530165399 specifications

The Poulan 530165399 is a high-performance chainsaw designed for both professional and home use, offering a blend of power, versatility, and user-friendly features. This model stands out for its ergonomic design, making it comfortable for extended use while minimizing user fatigue. It has a sturdy build, which ensures durability and resilience in demanding conditions.

One of the key features of the Poulan 530165399 is its powerful engine. It is equipped with a robust 42cc two-stroke engine that provides ample cutting power, making it suitable for various applications, from pruning trees to felling larger ones. The engine is designed for efficient fuel consumption, allowing users to maximize their operational time without frequent refueling.

A notable technology integrated into the Poulan 530165399 is the Easy Start feature, which allows for effortless ignition. This user-friendly technology is especially beneficial for those who may struggle with traditional starting methods. Additionally, the chainsaw features an automatic oiler system that ensures the chain remains lubricated during operation. This not only extends the life of the chain but also enhances cutting performance.

The chainsaw comes with a 16-inch bar and chain, providing an ideal balance between maneuverability and cutting capacity. Whether tackling thick branches or smaller logs, the Poulan 530165399 excels at delivering precise cuts. Furthermore, the chain tensioning system is designed for quick adjustments, allowing users to maintain optimal chain tension without the need for extra tools.

Safety is paramount in chainsaw design, and the Poulan 530165399 addresses this with features such as a wrap-around front handle and a chain brake. These components provide excellent control and protection against kickback, making it a safer choice for users at all skill levels.

In terms of maintenance, the Poulan 530165399 is engineered for ease of care. The air filter is easily accessible for cleaning or replacement, which helps maintain engine performance over time.

Overall, the Poulan 530165399 is a versatile chainsaw that combines power, safety, and convenience. Its features and technologies make it an excellent choice for anyone looking to handle outdoor cutting tasks efficiently. Whether you are a seasoned professional or a novice DIYer, this chainsaw can meet a wide range of cutting needs with reliability and ease.
Top Page Image Contents