Poulan 530087390 Braking function control, Inertia activating function control, Operating Tips

Page 10

Braking function control

CAUTION: The chain brake must be checked several times daily. The motor must be running when performing this procedure. This is the only instance when the saw should be placed on the ground with the motor running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front handle with your left hand. Squeeze trigger switch and allow motor to reach full speed. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the motor must not be running and the saw must be un- plugged from the power source.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14∀ (35 cm) above a stump or other wooden sur- face. Release your grip on the front han- dle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

OPERATING TIPS

SCheck chain tension before first use

and after 1 minute of operation. See CHECK CHAIN TENSION in the SER- VICE AND ADJUSTMENTS section.

SCut wood only. Do not cut metal, plas- tics, masonry, non-wood building mate- rials, etc.

SStop the saw if the chain strikes a for- eign object. Inspect the saw and repair parts as necessary.

S Keep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and increase the possibility of kickback.

S Practice cutting a few small logs using the following steps. This will help you get the “feel” of using your saw before you begin a major sawing operation.

SSqueeze trigger switch and allow unit

to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

SKeep the motor at full speed the en- tire time you are cutting.

S Release the trigger switch as soon as the cut is completed, allowing the motor to stop.

SKeep the cord away from the cutting

10

area. Position cord so it will not be caught on branches and the like dur- ing cutting.

S To avoid losing control when cut is complete, do not put pressure on saw at end of cut.

SStop motor before setting saw down.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cut- ting causing serious injury. Do not cut near buildings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be able to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree does make contact with any utility line, the utility company should be noti- fied immediately.

SCarefully plan your sawing operation in

advance.

SClear the work area. You need a clear area all around the tree so you can

have secure footing.

SThe chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause the tree to fall in a particular direction, such as:

S The wind direction and speed.

S The lean of the tree. The lean of a tree might not be apparent due to un- even or sloping terrain. Use a plumb or level to determine the direction of

tree lean.

SWeight and branches on one side. S Surrounding trees and obstacles.

SLook for decay and rot. If the trunk is rotted, it can snap and fall toward the operator.

SMake sure there is enough room for the tree to fall. Maintain a distance of 2-1/2tree lengths from the nearest

person or other objects. Noise can drown out a warning call.

SRemove dirt, stones, loose bark, nails, staples, and wire from the tree where cuts are to be made.

Plan a clear retreat path

Direction of Fall

45_

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Operate Your SAW Safely Plan AheadMaintain Your SAW in Good Working Order Maintain chain saw with care Electrical SafetyKeep oil cap and fasteners securely tightened PipesReduce the Chance Kickback Guard Against KickbackRotational Kickback can occur when Avoid Pinch-KickbackShoulder height Kickback Safety FeaturesMaintain Control Chain Brake and CKA AngleRapidly back towards the operator Sively upon safety devices built into your sawDouble Insulation Construction Attaching the BAR and Chain if not already attached Remove the plastic shipping spacer if presentKnow Your SAW Trigger SwitchChain Adjustment Screw Trigger LOCK-OUT ButtonOperating Instructions Power CordChain Tension Attach the Extension Cord to Your Chain SAWOperating Tips Braking function controlInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Bucking Felling Large TreesNotch CUT and Felling Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingGeneral Recommendations PruningCustomer Responsibilities Check for Damaged or Worn PartsCheck Chain Sharpness Unplug unit from the power sourceCheck Chain Tension Check Guide BARLubrication Inspect and Clean Unit and LabelsChain Replacement Chain SharpeningCustomer Serviceable Parts Chain AdjustmentSeasonal Storage Repair or replace Switch is Trigger switch failureTrouble Cause Remedy Sprocket wornElectrolux Home Products Electrolux Home PRODUCTS, INC

530087390 specifications

The Poulan 530087390 is a powerful and reliable chainsaw designed for both professional and recreational use, making it a fantastic choice for homeowners and landscapers alike. Known for its robust performance and user-friendly features, this chainsaw excels at tackling a variety of tasks, including cutting firewood, felling trees, and trimming branches.

One of the standout features of the Poulan 530087390 is its impressive engine. Equipped with a potent 42cc 2-cycle engine, this chainsaw delivers ample power for demanding cutting tasks while maintaining an efficient fuel consumption rate. The engine is specifically designed to provide reliable starting and smooth operation, ensuring that users can start their work with minimal hassle.

The Poulan 530087390 utilizes an advanced air filter system that enhances engine longevity and performance. This technology helps in reducing debris intake, resulting in cleaner air and better combustion. Additionally, the chainsaw incorporates an automatic oiling system that ensures the chain remains properly lubricated throughout operation, leading to reduced wear and enhanced cutting efficiency.

This chainsaw features a 16-inch bar and chain, striking a perfect balance between maneuverability and cutting capacity. The size makes it suitable for a range of tasks, from light pruning to medium-sized tree cutting, while the low-kickback chain design enhances safety during operation.

User comfort is also a priority in the design of the Poulan 530087390. The chainsaw is equipped with an ergonomic handle and anti-vibration technology, which helps reduce user fatigue during extended use. These features ensure that the chainsaw can be operated comfortably for longer periods, making it an ideal tool for both DIY enthusiasts and professionals alike.

In terms of safety, the Poulan 530087390 is equipped with essential safety features, including a chain brake that can be activated in case of kickback. This feature provides peace of mind for users, assuring them that safety is a primary concern in the design of this equipment.

Overall, the Poulan 530087390 stands out in the market due to its combination of power, efficiency, and user-friendly features. Whether tackling heavy-duty tasks or simple yard maintenance, this chainsaw provides dependable performance and exceptional value for money, making it a preferred choice among users who demand quality and reliability.
Top Page Image Contents