Starting a Cold Engine, Starting a Warm Engine

STARTING POSITION

Blower

Vacuum

WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to by- standers or the operator.

STARTING A COLD ENGINE

1.Move throttle lever to the position.

2.Move choke lever to the FULL CHOKE position.

3.Slowly press the primer button 8 times.

Throttle Lever					Primer Button

Choke Lever

4.Pull starter rope sharply until engine at- tempts to run, but no more than5 pulls (be- low 30_ F, 8 pulls).

NOTE: If engine attempts to start before the 5th pull, go to next step immediately.

5.Move the choke lever to the HALF CHOKE position.

6.Pull the starter rope sharply until the en- gine runs, but no more than 5 pulls (below 30_ F, 10 pulls).

7.After a 5 second warm--up, move the choke lever to the RUN position.

8.Allow the unit to run for 30 more seconds at the RUN position before moving the

throttle lever to position.

If engine has not started after 5 pulls (at HALF CHOKE), repeat STARTING A COLD ENGINE procedure. If engine still does not start, proceed to STARTING A FLOODED ENGINE.

9.To stop the engine, move the throttle lever to the STOP position.

STARTING A WARM ENGINE

NOTE: If fuel tank is empty, add fuel; then, follow STARTING A COLD ENGINE proce- dure. Do not fill fuel tank while engine is hot.

1.Move throttle lever to the position.

2.Pull starter rope sharply until engine runs, but no more than 5 pulls.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

3.To stop the engine, move the throttle lever to the STOP position.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position. Move throttle

lever to the fast position

; then, pull rope

until engine starts. After engine starts, move the

throttle lever to the slow position to allow engine to idle.

Starting could require pulling the starter rope many times depending on how badly the unit is flooded.

If unit still doesn’t start refer to the TROUBLE- SHOOTING TABLE or call 1-800-554-6723.

WARNING: Avoid touching muffler unless engine and muffler are cold. A hot muffler can cause serious burns.

WARNING: Stop engine and be sure the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

GENERAL RECOMMENDATIONS

Thewarranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as

instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot S Air Filter

S Housing Screws S Muffler

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SFuel Tank -- Do not use unit if fuel tank shows

signs of damage or leaks.

SVacuum Bag -- Do not use vacuum bag if it is torn or damaged.

-- 7 --

530163808 specifications

The Poulan 530163808 is a high-quality replacement chain designed for chainsaw enthusiasts and professionals who require durability and efficiency in challenging cutting conditions. Renowned for its performance, the 530163808 chain meets the needs of users looking for a reliable cutting tool for tree care, lumberjack tasks, or general woodwork.

One of the standout features of the Poulan 530163808 is its compatibility with a wide range of Poulan chainsaws, making it an excellent choice for those already invested in the Poulan ecosystem. This chain is engineered to provide a seamless fit and optimal performance, ensuring that users can efficiently replace worn-out chains with minimal hassle.

The Poulan 530163808 chain utilizes a unique cutting tooth design that enhances its cutting ability. Each tooth is crafted to achieve an efficient cutting angle, promoting faster and smoother cuts. This design not only increases productivity but also results in less strain on the chainsaw motor, which can lead to a longer lifespan for both the chain and the tool itself.

Another important characteristic of the Poulan 530163808 is its construction using high-quality materials. The chain is made of durable steel, providing a strong and resilient solution for heavy-duty cutting tasks. This material choice ensures that users can rely on the chain to withstand the rigors of continuous use in various environmental conditions, from dense forests to backyard pruning.

In addition to its robustness, the Poulan 530163808 features advanced processing techniques. The chain undergoes heat treatment, which influences its hardness and wear resistance, ultimately leading to prolonged life and reduced need for frequent replacements. This technology also helps maintain sharpness over time, allowing users to spend less time sharpening and more time cutting.

Overall, the Poulan 530163808 stands out as a top-tier replacement chain that embodies quality and performance. Whether for professional applications or personal projects, this chainsaw chain offers unmatched durability, efficiency, and compatibility. Chainsaw users can trust the Poulan 530163808 to help them tackle their cutting tasks with confidence and ease, ensuring that their tool remains in optimal working condition. With its innovative design and high-quality manufacturing, this chain is an investment in productivity and reliability for any woodcutting endeavor.