Poulan 530088073 Starting a Warm Engine, Starting a Flooded Engine, Clean AIR Filter

Page 6

SPull the starter rope sharply until the engine runs, but no more than 5 pulls (below 30_ F, 10 pulls). Run engine for 5 seconds, then

move choke lever to the RUN position.

SAllow the unit to run for 30 more seconds at the RUN position before moving the throttle

lever to position.

If engine has not started after 5 pulls (at HALF CHOKE), repeat STARTING A COLD ENGINE procedure. If engine still does not start, proceed to STARTING A FLOODED ENGINE.

STARTING A WARM ENGINE

S Move throttle lever to the

position.

SPull starter rope sharply until engine runs, but no more than 5 pulls.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

SMove the choke lever to the RUN position.

S

Move throttle lever to the

position.

S

Pull rope to clear engine of excess fuel.

 

This could require pulling the starter rope

many times.

SVacuum Bag -- Do not use vacuum bag if it is torn or damaged.

INSPECT AND CLEAN UNIT AND DECALS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild deter- gent.

SWipe off unit with a clean dry cloth.

CLEAN AIR FILTER

Air Filter

Cover

If unit still doesn’t start refer to the TROUBLE SHOOTING TABLE or call 1-800-554-6723.

Air Filter

Screws

WARNING: Avoid touching muffler unless engine and muffler are cold. A hot muffler can cause serious burns.

WARNING: Stop engine and be sure the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot S Air Filter

S Housing Screws S Muffler

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SFuel Tank -- Do not use unit if fuel tank shows signs of damage or leaks.

Cleaning the air filter:

A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean or replace air filter after every 5 hours of operation or yearly, whichever comes first.

SClean the cover and the area around it to keep debris from falling into the carburetor

chamber when the cover is removed.

SRemove parts as illustrated.

NOTE: Do not clean filter in gasoline or other flammable solvent. Doing so can create a fire hazard or produce harmful evaporative emis- sions.

SWash the filter in soap and water. S Allow filter to dry.

S Apply a few drops of oil to the filter; squeeze filter to distribute oil.

S Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch. Ignition timing is fixed, nonadjustable.

STwist, then pull off spark plug boot.

SRemove spark plug from cylinder and dis-

card.

S Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 in. socket wrench.

SReinstall the spark plug boot.

REPLACE FUEL FILTER

To replace fuel filter, drain unit by running it dry of fuel, then remove fuel cap/retainer assem- bly from tank. Pull filter from tank and remove it from the fuel line. Install new fuel filter on fuel line; reinstall parts.

-- 6 --

Image 6
Contents Manual de Instrucciones Manuel d’Instructions Handle Fuel with CAUTION, IT is Highly Flammable Know Your UnitPlan Ahead Operate Your Unit SafelyBlower Tube Assembly Vacuum BAG AssemblyMaintain Your Unit Properly Operating Position Vacuum Tube AssemblyShoulder Strap Adjustment Operating TipsSafely To Stop the EngineBefore Starting the Engine Blower VacuumStarting a Warm Engine Inspect and Clean Unit and DecalsClean AIR Filter Starting a Flooded EngineCheck Muffler Mounting Screws Carburetor AdjustmentsNeed a Service PART? Need ASSISTANCE?Troubleshooting Table Cause Remedy Service Centers Call 554 Maintenance Placement and Repair of Emission

530088073 specifications

The Poulan 530088073 is a versatile and reliable equipment part widely recognized for its performance and durability in various outdoor tools. This product primarily serves as a crucial component for Poulan chainsaws and other outdoor machinery, significantly enhancing their efficiency.

One of the standout features of the Poulan 530088073 is its compatibility with a range of chain saw models, making it an essential replacement part for users looking to maintain their tools. Its design adheres to the original equipment specifications, ensuring a perfect fit and optimal performance. The installation process is straightforward, allowing users to quickly replace worn or damaged components without requiring extensive mechanical knowledge.

In terms of technology, the Poulan 530088073 incorporates advanced manufacturing processes that enhance its durability and longevity. Crafted from high-quality materials, this part is engineered to withstand the rigors of outdoor use, resisting wear and tear even in challenging conditions. The robust design minimizes the risk of failure during operation, ensuring a safer and more reliable experience for the user.

Another notable characteristic of the Poulan 530088073 is its role in improving the overall functionality of chainsaws. By replacing worn-out parts with this reliable component, users can restore their equipment to peak performance levels. The enhanced efficiency translates to quicker cutting speeds and cleaner cuts, making tasks easier and more efficient.

Moreover, this part's compatibility with various Poulan models highlights its versatility, appealing to both casual users and professional landscapers. By investing in the Poulan 530088073, users can significantly extend the lifespan of their equipment, ensuring that they get the most value out of their purchase.

In conclusion, the Poulan 530088073 stands out as a top choice for those in need of reliable replacement parts for their outdoor tools. With features that prioritize compatibility, durability, and enhanced performance, it is a critical component for maintaining chainsaws and other machinery. Users can trust this part to deliver the efficiency and reliability they need for successful outdoor projects.