Poulan 115274026, 952711880 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Cold Engine

Page 10

WARNING: Alternative fuels (not gas- oline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HOW TO STOP YOUR UNIT

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch. The switch will automatically return to the ON position. Wait 5 seconds before at- tempting to restart unit to allow switch to reset.

ON/STOP

Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move the start lever to the START posi- tion.

Primer Bulb

Start Lever

Starter Handle

4.Pull starter rope handle sharply until en- gine starts and runs.

5.Allow unit to run for 10--15 seconds, then fully squeeze the throttle trigger to disen- gage the starting system.

STARTING A WARM ENGINE

1.Squeeze and hold the throttle trigger.

Keep throttle trigger fully squeezed until engine runs smoothly..

3.Pull starter rope sharply while squeezing

throttle trigger until engine runs. NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned off. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the start lever to the RUN position. Fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL:

Edger . . . . . . . . . . . . . . . . . . . . . PP1000E

Cultivator . . . . . . . . . . . . . . . . . . PP2000T

Blower . . . . . . . . . . . . . . . . . . . . PP3000B

Pruner . . . . . . . . . . . . . . . . . . . . PP5000P

Pruner . . . . . . . . . . . . . . . . . . . . PP5500P

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Fuel Safety Operator SafetyUNIT/MAINTENANCE Safety Cutting SafetyInstalling Brushcutter Attachment AssemblyCarton Contents Transporting and StorageAttaching the Handlebar Assembly of Shoulder StrapTo Relocate Shoulder Strap Clamp Right side of your waistAssembly Information Weed Blade Configuring Your UnitAssembly Information Trimmer Head Attaching the Plastic Shield and Trimmer HeadInstallation of the Metal Blade Attaching the Metal ShieldOperation Starting a Cold Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Warm EngineOperating Position Installing Optional ATTACH- MentsRemoving Trimmer ATTACH- Ment or Other Optional Attachments Operating Instructions for USE with Trimmer HeadTip of the line Cutting MethodsOperating Instructions for USE with Weed Blade Does the cutting Work areaAdditional Safety Rules Edger SafetyHedge Trimmer Safety BLOWER/VACUUM SafetyCultivator Safety Pole Pruner SafetySnow Thrower Safety Know how to stop quicklyMaintenance Carburetor Idle Speed Adjustment Service and AdjustmentsBlade Replacement Replacing the LineEngine Seasonal StorageFuel System OtherTroubleshooting Table Cause Remedy Canada, contact Limited WarrantyStatesville Road Ligations The U.S. EnvironmentalIntermediate 125 hours Extended 300 hours

952711880, 115274026 specifications

The Poulan 952711880 and 115274026 are essential components in the world of outdoor power equipment, specifically designed to enhance the performance of various Poulan chainsaws. These two model numbers pertain to vital accessories that contribute to the functionality and efficiency of chainsaws, ensuring that they operate smoothly and effectively in a range of cutting applications.

The Poulan 952711880 is primarily a replacement chain, known for its durable design and reliable performance. This chain features a unique cutting tooth design that allows for efficient wood cutting, making it ideal for both professional and hobbyist lumberjacks. The 952711880 is designed to provide optimal cutting efficiency, reducing the effort needed to fell trees, prune limbs, or cut firewood. Its high carbon steel construction not only enhances durability but also ensures that the chain maintains its sharpness over extended periods, minimizing the need for frequent sharpening.

On the other hand, the Poulan 115274026 is known for its compatibility with various Poulan chainsaw models. This model number represents a replacement part, specifically a guide bar, which plays a crucial role in the overall operation of the chainsaw. The guide bar is designed to provide stability and support during cutting, allowing for precise maneuvers and reducing the risk of kickback. Made from high-quality materials, the 115274026 guide bar is lightweight yet robust, making it easy to handle while ensuring that it can withstand the rigors of heavy-duty use.

Both the 952711880 chain and the 115274026 guide bar incorporate cutting-edge technologies to enhance performance. For instance, the chain features low-vibration technology, which results in less strain on the user and contributes to a more comfortable cutting experience. Additionally, both accessories are engineered for easy installation, allowing users to quickly and conveniently replace worn-out parts without tedious adjustments.

In summary, the Poulan 952711880 and 115274026 are vital components that significantly enhance the performance, efficiency, and safety of Poulan chainsaws. With their durable construction, innovative technologies, and user-friendly design, these accessories are essential for anyone looking to maximize their chainsaw's capabilities, whether for residential property maintenance or professional logging tasks. Investing in these reliable parts ensures that users can tackle any cutting project with confidence and ease.
Top Page Image Contents