Poulan 115274026, 952711880 Assembly of Shoulder Strap, To Relocate Shoulder Strap Clamp

Page 6

4.Position locking/release button of attach- ment into guide recess of coupler.

5.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

6.Before using the unit, tighten the knob se- curely by turning clockwise.

Coupler Primary Hole

Guide Recess

Locking/

Upper Release Attachment

Shaft Button

WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before op- erating the unit. All attachments are designed to be used in the primary hole unless other- wise stated in the applicable attachment in- struction manual. Using the wrong hole could lead to serious injury or damage to the unit.

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit.

1.Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the

right side of your waist.

NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder.

2.Adjust the strap, allowing the hook to be about 6 inches (15 cm) below the waist.

3.Fasten the strap hook to the clamp located between the trigger handle and the handle- bar clamp base and lift the tool to the oper- ating position.

4.Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation.

NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit.

TO RELOCATE SHOULDER STRAP CLAMP:

1.Loosen and remove both clamp screws.

2.Place the upper shoulder strap clamp over the shaft.

3.Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes.

Locking/Release

Button in Primary Hole

For assembly of optional attachments (see list on page 10), refer to the ASSEMBLY section of the applicable attachment instruction manual.

ATTACHING THE HANDLEBAR

DANGER: To avoid serious injury, the barrier portion of the handlebar must be installed as shown to provide a barrier between operator and the spinning blade.

Lower Shoulder Strap Clamp

Upper Shoulder

Strap Clamp

Screws

1.Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow.

2.Position the bracket cover over the han- dlebar. Again make sure the handlebar is at the end of the arrow.

3.Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench.

Handlebar Screw

Bracket Cover

Mounting Bracket

4.Insert two screws into the screw holes.

5.Secure shoulder strap clamp by tighten- ing screws with a hex wrench.

HARNESS

ADJUSTMENT

FOR BALANCE

6 inches

 

 

4 -- 12 inches

(15 cm)

 

 

 

 

 

(10 -- 30 cm)

below

 

 

 

 

30 inches

 

above

waist

 

 

 

(76 cm)

 

ground

 

 

 

 

 

 

 

 

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Fuel Safety Operator SafetyUNIT/MAINTENANCE Safety Cutting SafetyInstalling Brushcutter Attachment AssemblyCarton Contents Transporting and StorageAttaching the Handlebar Assembly of Shoulder StrapTo Relocate Shoulder Strap Clamp Right side of your waistAssembly Information Weed Blade Configuring Your UnitAssembly Information Trimmer Head Attaching the Plastic Shield and Trimmer HeadInstallation of the Metal Blade Attaching the Metal ShieldOperation Starting a Cold Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Warm EngineOperating Position Installing Optional ATTACH- MentsRemoving Trimmer ATTACH- Ment or Other Optional Attachments Operating Instructions for USE with Trimmer HeadTip of the line Cutting MethodsOperating Instructions for USE with Weed Blade Does the cutting Work areaAdditional Safety Rules Edger SafetyHedge Trimmer Safety BLOWER/VACUUM SafetyCultivator Safety Pole Pruner SafetySnow Thrower Safety Know how to stop quicklyMaintenance Carburetor Idle Speed Adjustment Service and AdjustmentsBlade Replacement Replacing the LineEngine Seasonal StorageFuel System OtherTroubleshooting Table Cause Remedy Canada, contact Limited WarrantyStatesville Road Ligations The U.S. EnvironmentalIntermediate 125 hours Extended 300 hours

952711880, 115274026 specifications

The Poulan 952711880 and 115274026 are essential components in the world of outdoor power equipment, specifically designed to enhance the performance of various Poulan chainsaws. These two model numbers pertain to vital accessories that contribute to the functionality and efficiency of chainsaws, ensuring that they operate smoothly and effectively in a range of cutting applications.

The Poulan 952711880 is primarily a replacement chain, known for its durable design and reliable performance. This chain features a unique cutting tooth design that allows for efficient wood cutting, making it ideal for both professional and hobbyist lumberjacks. The 952711880 is designed to provide optimal cutting efficiency, reducing the effort needed to fell trees, prune limbs, or cut firewood. Its high carbon steel construction not only enhances durability but also ensures that the chain maintains its sharpness over extended periods, minimizing the need for frequent sharpening.

On the other hand, the Poulan 115274026 is known for its compatibility with various Poulan chainsaw models. This model number represents a replacement part, specifically a guide bar, which plays a crucial role in the overall operation of the chainsaw. The guide bar is designed to provide stability and support during cutting, allowing for precise maneuvers and reducing the risk of kickback. Made from high-quality materials, the 115274026 guide bar is lightweight yet robust, making it easy to handle while ensuring that it can withstand the rigors of heavy-duty use.

Both the 952711880 chain and the 115274026 guide bar incorporate cutting-edge technologies to enhance performance. For instance, the chain features low-vibration technology, which results in less strain on the user and contributes to a more comfortable cutting experience. Additionally, both accessories are engineered for easy installation, allowing users to quickly and conveniently replace worn-out parts without tedious adjustments.

In summary, the Poulan 952711880 and 115274026 are vital components that significantly enhance the performance, efficiency, and safety of Poulan chainsaws. With their durable construction, innovative technologies, and user-friendly design, these accessories are essential for anyone looking to maximize their chainsaw's capabilities, whether for residential property maintenance or professional logging tasks. Investing in these reliable parts ensures that users can tackle any cutting project with confidence and ease.
Top Page Image Contents