Poulan 952711880, 115274026 Service and Adjustments, Replacing the Line, Blade Replacement

Page 17

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

For unit to operate properly, the cutting line should be replaced when line becomes worn to less than 3 inches (7.5 cm) in length from the edge of the line exit tunnels on each side of the cutting head.

1.Remove and discard worn line before installing new line.

2.Use only 0.115 inch (3 mm) diameter Poulan PRO brand cut length line.

3.Insert one end of the line through the positioning tunnel.

4.Continue to feed line through tunnel until line is centered (leaving equal amounts on each side). See illustration below.

Positioning tunnel

5.Insert ends of line one at a time through the line exit tunnels.

6.Pull the line and make sure the line is ex- tended fully through the tunnels.

Line exit

Line exit

tunnel

tunnel

7.Correctly installed line will be the same length on both ends.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade re- placement instructions and illustrations.

CARBURETOR IDLE SPEED ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head, blade or any optional attachment will be spinning during most of this procedure. Wear your protective equipment and observe all safe- ty precautions. After making adjustments, the trimmer head, blade or any optional attachment must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head, blade or optional attachment moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine runs without trimmer head, blade or optional attachment moving or spinning (idle too fast) or stalling (idle speed too slow).

S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head, blade or optional attachment moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head, blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules UNIT/MAINTENANCE Safety Operator SafetyFuel Safety Cutting SafetyCarton Contents AssemblyInstalling Brushcutter Attachment Transporting and StorageTo Relocate Shoulder Strap Clamp Assembly of Shoulder StrapAttaching the Handlebar Right side of your waistAssembly Information Trimmer Head Configuring Your UnitAssembly Information Weed Blade Attaching the Plastic Shield and Trimmer HeadAttaching the Metal Shield Installation of the Metal BladeOperation HOW to Start Your Unit HOW to Stop Your UnitStarting a Cold Engine Starting a Warm EngineRemoving Trimmer ATTACH- Ment or Other Optional Attachments Installing Optional ATTACH- MentsOperating Position Operating Instructions for USE with Trimmer HeadOperating Instructions for USE with Weed Blade Cutting MethodsTip of the line Does the cutting Work areaEdger Safety Additional Safety RulesCultivator Safety BLOWER/VACUUM SafetyHedge Trimmer Safety Pole Pruner SafetyKnow how to stop quickly Snow Thrower SafetyMaintenance Blade Replacement Service and AdjustmentsCarburetor Idle Speed Adjustment Replacing the LineFuel System Seasonal StorageEngine OtherTroubleshooting Table Cause Remedy Statesville Road Limited WarrantyCanada, contact Ligations The U.S. EnvironmentalIntermediate 125 hours Extended 300 hours

952711880, 115274026 specifications

The Poulan 952711880 and 115274026 are essential components in the world of outdoor power equipment, specifically designed to enhance the performance of various Poulan chainsaws. These two model numbers pertain to vital accessories that contribute to the functionality and efficiency of chainsaws, ensuring that they operate smoothly and effectively in a range of cutting applications.

The Poulan 952711880 is primarily a replacement chain, known for its durable design and reliable performance. This chain features a unique cutting tooth design that allows for efficient wood cutting, making it ideal for both professional and hobbyist lumberjacks. The 952711880 is designed to provide optimal cutting efficiency, reducing the effort needed to fell trees, prune limbs, or cut firewood. Its high carbon steel construction not only enhances durability but also ensures that the chain maintains its sharpness over extended periods, minimizing the need for frequent sharpening.

On the other hand, the Poulan 115274026 is known for its compatibility with various Poulan chainsaw models. This model number represents a replacement part, specifically a guide bar, which plays a crucial role in the overall operation of the chainsaw. The guide bar is designed to provide stability and support during cutting, allowing for precise maneuvers and reducing the risk of kickback. Made from high-quality materials, the 115274026 guide bar is lightweight yet robust, making it easy to handle while ensuring that it can withstand the rigors of heavy-duty use.

Both the 952711880 chain and the 115274026 guide bar incorporate cutting-edge technologies to enhance performance. For instance, the chain features low-vibration technology, which results in less strain on the user and contributes to a more comfortable cutting experience. Additionally, both accessories are engineered for easy installation, allowing users to quickly and conveniently replace worn-out parts without tedious adjustments.

In summary, the Poulan 952711880 and 115274026 are vital components that significantly enhance the performance, efficiency, and safety of Poulan chainsaws. With their durable construction, innovative technologies, and user-friendly design, these accessories are essential for anyone looking to maximize their chainsaw's capabilities, whether for residential property maintenance or professional logging tasks. Investing in these reliable parts ensures that users can tackle any cutting project with confidence and ease.
Top Page Image Contents