Poulan 220 LE, 260 LE Starting a Warm Engine, Difficult Starting or starting a flooded engine

Page 10

ON/STOP

Switch

Primer

Bulb

ON/STOP SWITCH

ON STOP

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

S When cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/Fast OFF FULL

Idle Lever

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the full extent, then push the lever back in com- pletely (to the OFF position).

3.Slowly press the primer bulb 6 times.

4.Pull the starter rope quickly with your right hand until the engine starts.

5.Squeeze and release throttle trigger, al- lowing engine to idle.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020! (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14! (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials,

etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackMaintain Control Kickback Safety FeaturesReduce the Chance Kickback Your left arm straight with the elbow lockedComputed kickback angle CKA Table Chain Brake and CKA AngleFront Hand Guard, designed to reduce Attaching the BAR & Chain If not Tip BarChain Tension Including units with chain already installed Adjusting the tensionChecking the tension Throttle Trigger ON/STOP SwitchKnow Your SAW Throttle LockoutImportant Points to Remember Fueling EngineBAR and Chain Lubrication Handle Right foot through rear handleBraking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Gine can resultTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points Cleaning the air filterPruning LimbingInspect Muffler and Spark Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment Arresting ScreenChain Sharpening BAR MaintenanceNeed Service PART? Ignition TimingTroubleshooting Table Cause Remedy Your Warranty Rights and Obliga Tions The U.S. Environmental Protection

220 LE, 260 LE specifications

The Poulan 220 LE and 260 LE are two powerful chainsaws designed for both professional landscapers and DIY enthusiasts. These models are known for their reliability, efficiency, and ease of use, making them popular choices for various cutting tasks.

The Poulan 220 LE is powered by a robust 20cc engine, providing ample power for light to medium cutting tasks. Its lightweight build enhances maneuverability, allowing users to operate it for extended periods without fatigue. The chainsaw features a 10-inch bar, ideal for trimming branches, pruning, and handling smaller trees, making it a suitable choice for homeowners and gardeners. One of the standout features of the 220 LE is its tool-less chain tensioning system, allowing users to make quick adjustments to the chain without the need for additional tools. This ensures safety and convenience, as maintaining optimal chain tension is vital for performance and safety.

Conversely, the Poulan 260 LE offers a more powerful option with its 26cc engine. This model is designed for heavier cutting tasks, making it suitable for those who require a more robust tool for larger projects. The 16-inch bar allows for cutting through thicker logs and branches with ease. The 260 LE is equipped with the same user-friendly tool-less chain tensioning system, ensuring that users can maintain their chainsaw quickly and efficiently.

Both models incorporate advanced technologies to enhance performance and user experience. The Easy Start system reduces the effort needed to start the engine, allowing for quicker and smoother operation. Additionally, the anti-vibration design minimizes operator fatigue, providing a more comfortable cutting experience.

Both models are built with durability in mind, featuring high-quality components that withstand heavy use. Their air filter systems help maintain engine performance by keeping out dirt and debris, which is crucial for longevity.

In summary, the Poulan 220 LE and 260 LE chainsaws blend power, ease of use, and comfort in a compact design. Whether for occasional yard work or more extensive landscaping projects, these models stand out as reliable tools that meet a variety of cutting needs. Their advanced technologies and user-friendly features make them excellent choices for anyone looking to effectively tackle their cutting tasks.
Top Page Image Contents