Poulan 220 LE, 260 LE instruction manual Checking the tension, Adjusting the tension

Page 7

Cutters

Depth Gauge

 

 

 

 

 

 

 

 

Drive Links

6.Place the chain over and behind the clutch, fitting the drive links in the clutch drum sprocket.

Place chain onto the sprocket

7.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

8.Fit chain drive links in to bar groove.

9.Pull the bar forward until the chain is snug in the groove of the bar. Ensure all drive links are in the bar groove.

10.Hold guide bar against the saw frame and install the chain brake.

11.Replace the chain brake nuts and tighten finger tight. Once the chain is tensioned you will need to tighten chain brake nuts.

CHAIN TENSION (Including units with chain already installed)

NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move the chain around the bar. If the chain does not rotate, it is too tight. If too loose, the chain will sag below the bar.

Adjusting the tension:

Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

An adjusting screw (located on the guide bar) is used to adjust the tension of the chain (see illustration).

1.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Guide bar

Adjusting

Screw

2.Using the screwdriver end of the bar tool, roll chain around guide bar to ensure all links are in bar groove.

3.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn adjust- ing screw until sag does not exist.

4.Tighten bar clamp nuts securely with the bar tool.

Chain Brake

Nuts

5.Use the screwdriver end of the bar tool to move chain around guide bar.

6.If chain does not rotate, it is too tight. Slightly loosen bar clamp nuts and loos- en chain by turning the adjusting screw. Retighten bar clamp nuts.

7.If chain is too loose, it will sag below the guide bar. DO NOT operate the saw if the chain is loose.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionYour left arm straight with the elbow locked Kickback Safety FeaturesReduce the Chance Kickback Maintain ControlComputed kickback angle CKA Table Chain Brake and CKA AngleFront Hand Guard, designed to reduce Tip Bar Attaching the BAR & Chain If notChain Tension Including units with chain already installed Adjusting the tensionChecking the tension Throttle Lockout ON/STOP SwitchKnow Your SAW Throttle TriggerHandle Right foot through rear handle Fueling EngineBAR and Chain Lubrication Important Points to RememberInertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beGine can result Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing Cleaning the air filterPruning Limbing and Pruning Important PointsArresting Screen Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment Inspect Muffler and SparkIgnition Timing BAR MaintenanceNeed Service PART? Chain SharpeningTroubleshooting Table Cause Remedy Tions The U.S. Environmental Protection Your Warranty Rights and Obliga

220 LE, 260 LE specifications

The Poulan 220 LE and 260 LE are two powerful chainsaws designed for both professional landscapers and DIY enthusiasts. These models are known for their reliability, efficiency, and ease of use, making them popular choices for various cutting tasks.

The Poulan 220 LE is powered by a robust 20cc engine, providing ample power for light to medium cutting tasks. Its lightweight build enhances maneuverability, allowing users to operate it for extended periods without fatigue. The chainsaw features a 10-inch bar, ideal for trimming branches, pruning, and handling smaller trees, making it a suitable choice for homeowners and gardeners. One of the standout features of the 220 LE is its tool-less chain tensioning system, allowing users to make quick adjustments to the chain without the need for additional tools. This ensures safety and convenience, as maintaining optimal chain tension is vital for performance and safety.

Conversely, the Poulan 260 LE offers a more powerful option with its 26cc engine. This model is designed for heavier cutting tasks, making it suitable for those who require a more robust tool for larger projects. The 16-inch bar allows for cutting through thicker logs and branches with ease. The 260 LE is equipped with the same user-friendly tool-less chain tensioning system, ensuring that users can maintain their chainsaw quickly and efficiently.

Both models incorporate advanced technologies to enhance performance and user experience. The Easy Start system reduces the effort needed to start the engine, allowing for quicker and smoother operation. Additionally, the anti-vibration design minimizes operator fatigue, providing a more comfortable cutting experience.

Both models are built with durability in mind, featuring high-quality components that withstand heavy use. Their air filter systems help maintain engine performance by keeping out dirt and debris, which is crucial for longevity.

In summary, the Poulan 220 LE and 260 LE chainsaws blend power, ease of use, and comfort in a compact design. Whether for occasional yard work or more extensive landscaping projects, these models stand out as reliable tools that meet a variety of cutting needs. Their advanced technologies and user-friendly features make them excellent choices for anyone looking to effectively tackle their cutting tasks.
Top Page Image Contents