Poulan 220 LE, 260 LE instruction manual Cutting a Fallen Tree, Types of Cutting Used for Bucking

Page 12

S DO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

SCut shattered wood very carefully; sharp pieces of wood could be flung toward oper-

ator.

SUse a sawhorse to cut small logs. Never allow another person to hold the log while

cutting and never hold the log with your leg or foot.

S Do not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A

SUPPORT

SOvercut through 1/3 of the diameter of the log.

SRoll the log over and finish with a second

overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR SUPPORT STAND

SRemember your first cut is always on the compression side of the log.

(Refer to the illustrations below for your

first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

Using a log for support

2nd Cut

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

2nd Cut

12

1st Cut

1st Cut

Image 12
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance KickbackMaintain Control Your left arm straight with the elbow lockedChain Brake and CKA Angle Computed kickback angle CKA TableFront Hand Guard, designed to reduce Attaching the BAR & Chain If not Tip BarAdjusting the tension Chain Tension Including units with chain already installedChecking the tension ON/STOP Switch Know Your SAWThrottle Trigger Throttle LockoutFueling Engine BAR and Chain LubricationImportant Points to Remember Handle Right foot through rear handleStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlTree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Gine can resultBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportCleaning the air filter PruningLimbing and Pruning Important Points LimbingCleaning the Spark ARREST- ING Screen Carburetor AdjustmentInspect Muffler and Spark Arresting ScreenBAR Maintenance Need Service PART?Chain Sharpening Ignition TimingTroubleshooting Table Cause Remedy Your Warranty Rights and Obliga Tions The U.S. Environmental Protection

220 LE, 260 LE specifications

The Poulan 220 LE and 260 LE are two powerful chainsaws designed for both professional landscapers and DIY enthusiasts. These models are known for their reliability, efficiency, and ease of use, making them popular choices for various cutting tasks.

The Poulan 220 LE is powered by a robust 20cc engine, providing ample power for light to medium cutting tasks. Its lightweight build enhances maneuverability, allowing users to operate it for extended periods without fatigue. The chainsaw features a 10-inch bar, ideal for trimming branches, pruning, and handling smaller trees, making it a suitable choice for homeowners and gardeners. One of the standout features of the 220 LE is its tool-less chain tensioning system, allowing users to make quick adjustments to the chain without the need for additional tools. This ensures safety and convenience, as maintaining optimal chain tension is vital for performance and safety.

Conversely, the Poulan 260 LE offers a more powerful option with its 26cc engine. This model is designed for heavier cutting tasks, making it suitable for those who require a more robust tool for larger projects. The 16-inch bar allows for cutting through thicker logs and branches with ease. The 260 LE is equipped with the same user-friendly tool-less chain tensioning system, ensuring that users can maintain their chainsaw quickly and efficiently.

Both models incorporate advanced technologies to enhance performance and user experience. The Easy Start system reduces the effort needed to start the engine, allowing for quicker and smoother operation. Additionally, the anti-vibration design minimizes operator fatigue, providing a more comfortable cutting experience.

Both models are built with durability in mind, featuring high-quality components that withstand heavy use. Their air filter systems help maintain engine performance by keeping out dirt and debris, which is crucial for longevity.

In summary, the Poulan 220 LE and 260 LE chainsaws blend power, ease of use, and comfort in a compact design. Whether for occasional yard work or more extensive landscaping projects, these models stand out as reliable tools that meet a variety of cutting needs. Their advanced technologies and user-friendly features make them excellent choices for anyone looking to effectively tackle their cutting tasks.