Poulan 222 Chain Brake and CKA Angle, Front Hand Guard, designed to reduce, Length

Page 5

Reduced Kickback Symmetrical Guide Bar

Small Radius Tip

Symmetrical Guide Bar

Large Radius Tip

S Low--Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Low-- Kickback Chain has met kickback per- formance requirements when tested on a representative sample of chain saws be- low 3.8 cubic inch displacement specified in ANSI B175.1.

Contoured Depth Gauge

 

Elongated Guard Link

 

Deflects

Low--- Kickback

kickback force

and allows wood

Chain

to gradually ride

 

into cutter

 

Can Obstruct Material

Not a Low--- Kickback Chain

SFront Hand Guard, designed to reduce the

chance of your left hand contacting the chain if your hand slips off the front handlebar.

SPosition of front and rear handlebars, de- signed with distance between handles and “in-line” with each other. The spread and “in-line” position of the hands provided by this design work together to give balance and resistance in controlling the pivot of the saw back toward the operator if kick- back occurs.

CHAIN BRAKE AND CKA ANGLE

SChain Brake, designed to stop the chain in the event of kickback.

WARNING: WE DO NOT REP- RESENT AND YOU SHOULD NOT AS- SUME THAT THE CHAIN BRAKE WILL PROTECT YOU IN THE EVENT OF A KICK- BACK. Kickback is a lightning fast action which throws the bar and rotating chain back and up toward the operator. Kickback can be

caused by allowing contact of the bar tip in the danger zone with any hard object. Kickback can also be caused by pinching the saw chain along the top of the guide bar. This action may push the guide bar rapidly back toward the op- erator. Either of these events may cause you to lose control of the saw which could result in serious injury or even death. DO NOT RELY UPON ANY OF THE DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Reduced--kickback guide bars and low--kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kickback chain and bar as original equipment. Repairs on a chain brake should be made by an autho- rized servicing dealer. Take your unit to the place of purchase if purchased from a servic- ing dealer, or to the nearest authorized master service dealer.

STip contact in some cases may cause a light- ning fast reverse REACTION, kicking guide bar up and back toward operator.

SPinching the saw chain along the top of the guide bar may push the guide bar rapidly

back toward the operator.

SEither of these reactions may cause you to lose control of the saw which could result in serious injury. Do not rely exclusively upon devices built into your saw.

WARNING: Computed kickback angle (CKA) listed on your saw and listed in the CKA table below represents angle of kickback your bar and chain combinations will have when tested in accordance with CSA (Cana- dian Standards Association) and ANSI stan- dards. When purchasing replacement bar and chain, considerations should be given to the lower CKA values. Lower CKA values repre- sent safer angles to the user, higher values in- dicate more angle and higher kick energies. Computed angles represented indicate total energy and angle associated without activation of the chain brake during kickback. Activated angle represents chain stopping time relative to activation angle of chain break and resulting kick angle of saw. In all cases lower CKA val- ues represent a safer operating environment for the user.

The following guide bar and chain combina- tions meet kickback requirements of CSA Standards Z62.1, Z62.3, & ANSI B175.1 when used on saws listed in this manual. Use of bar and chain combinations other than those listed is not recommended and may not meet the CKA requirements per standard.

Computed kickback angle (CKA) Table

 

BAR

 

 

 

CKA without chain brake

MODEL

P/N

Length

 

CHAIN P/N

222

530044834

16″

952051211

19_

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents English Español Français Manual de Instrucciones Manuel d’InstructionsPlan Ahead Identification of SymbolsSafety Rules Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Kickback Safety FeaturesReduce the Chance of Kickback Front Hand Guard, designed to reduce Chain Brake and CKA AngleBack toward the operator LengthAttaching the BAR & Chain If not AssemblyChain Brake Nuts Mount the BarAdjusting the tension Chain Tension Including units with chain already installedChecking the tension CuttersKnow Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine StartingBAR and Chain Lubrication Important Points to RememberImportant Points Cutting MethodsStarting a Warm Engine Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Direction of FallCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points ServiceLimbing PruningCleaning the Spark ARREST- ING Screen Cleaning the air filterAIR Filter Inspect Muffler and Spark Arresting ScreenBAR Maintenance Carburetor AdjustmentChain Sharpening Ignition TimingNeed ASSISTANCE? Need Service PART?Storage Need ASSISTANCE?Tions The U.S. Environmental Protection Limited WarrantyPlacement and Repair of Emission

222 specifications

The Poulan 222 is a versatile and powerful chain saw designed to meet the demands of both casual users and professionals alike. Renowned for its reliability and performance, the Poulan 222 is an excellent addition to the toolkits of landscapers, tree surgeons, and homeowners who require a dependable cutting tool for various tasks.

One of the standout features of the Poulan 222 is its lightweight design. Weighing in at just under 11 pounds, this chain saw is easy to maneuver, allowing users to work for extended periods without excessive fatigue. The balanced weight distribution also contributes to stability during operation, enhancing precision cuts.

The Poulan 222 is powered by a robust 2-cycle engine, delivering exceptional cutting power for both light and heavy-duty applications. With a displacement of 45cc, this engine is capable of producing up to 2.0 horsepower, which means it can handle tough materials like hardwood with efficiency. This power is complemented by a quality chain bar, typically measuring 18 inches in length, providing the right length for a variety of cutting tasks.

One of the key technologies in the Poulan 222 is its Easy Start feature. This innovative system significantly reduces the amount of effort needed to pull the starter rope, making it easier to start the saw with less physical exertion. Additionally, the chain saw incorporates a primer bulb that ensures fuel reaches the engine quickly, further aiding in starting.

The Poulan 222 is designed with user safety and comfort in mind. It features an inertia-activated chain brake that helps prevent accidents in case of kickback, a common hazard when operating a chain saw. The ergonomic handle and anti-vibration technology contribute to a more comfortable grip, reducing strain during prolonged use.

Another noteworthy characteristic of the Poulan 222 is its fuel efficiency. The engine is designed to consume less fuel while providing high performance, leading to fewer stops for refueling and increased productivity during work sessions.

Overall, the Poulan 222 is a well-rounded chain saw that combines power, comfort, and advanced features. Whether tackling home improvement projects, maintaining a landscape, or executing professional tree work, the Poulan 222 stands out as a reliable and efficient tool. It represents a smart investment for anyone looking to enhance their cutting capabilities with a saw that delivers both power and precision.
Top Page Image Contents