Poulan 222 Chain Tension Including units with chain already installed, Checking the tension

Page 7

Cutters

Depth Gauge

 

Drive Links

6.Place the chain over and behind the clutch, fitting the drive links in the clutch drum sprocket.

Place chain onto the sprocket

7.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

8.Fit chain drive links in to bar groove.

9.Pull the bar forward until the chain is snug in the groove of the bar. Ensure all drive links are in the bar groove.

10.Hold guide bar against the saw frame and install the chain brake.

11.Replace the chain brake nuts and tight- en finger tight. Once the chain is ten- sioned you will need to tighten chain brake nuts.

CHAIN TENSION (Including units with chain already installed)

When adjusting chain tension, make sure the chain brake nuts are finger tight only. At- tempting to tension the chain when the chain brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move the chain around the bar. If the chain does not rotate, it is too tight. If too loose, the chain will sag below the bar.

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

An adjusting screw (located on the guide bar) is used to adjust the tension of the chain (see illustration).

STurn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Guide bar

Adjusting

Screw

SUsing the screwdriver end of the bar tool,

roll chain around guide bar to ensure all links are in bar groove.

SLift up tip of guide bar to check for sag. Re- lease tip of guide bar, then turn adjusting screw until sag does not exist.

STighten bar clamp nuts securely with the bar tool.

Chain Brake

Nuts

SUse the screwdriver end of the bar tool to

move chain around guide bar.

S If chain does not rotate, it is too tight. Slightly loosen bar clamp nuts and loosen chain by turning the adjusting screw. Re- tighten bar clamp nuts.

SIf chain is too loose, it will sag below the guide bar.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents English Español Français Manual de Instrucciones Manuel d’InstructionsSafety Rules Identification of SymbolsPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Length Chain Brake and CKA AngleFront Hand Guard, designed to reduce Back toward the operatorMount the Bar AssemblyAttaching the BAR & Chain If not Chain Brake NutsCutters Chain Tension Including units with chain already installedAdjusting the tension Checking the tensionThrottle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationStarting a Warm Engine Cutting MethodsImportant Points Direction of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen AIR FilterIgnition Timing Carburetor AdjustmentBAR Maintenance Chain SharpeningNeed ASSISTANCE? Need Service PART?Need ASSISTANCE? StorageTions The U.S. Environmental Protection Limited WarrantyPlacement and Repair of Emission

222 specifications

The Poulan 222 is a versatile and powerful chain saw designed to meet the demands of both casual users and professionals alike. Renowned for its reliability and performance, the Poulan 222 is an excellent addition to the toolkits of landscapers, tree surgeons, and homeowners who require a dependable cutting tool for various tasks.

One of the standout features of the Poulan 222 is its lightweight design. Weighing in at just under 11 pounds, this chain saw is easy to maneuver, allowing users to work for extended periods without excessive fatigue. The balanced weight distribution also contributes to stability during operation, enhancing precision cuts.

The Poulan 222 is powered by a robust 2-cycle engine, delivering exceptional cutting power for both light and heavy-duty applications. With a displacement of 45cc, this engine is capable of producing up to 2.0 horsepower, which means it can handle tough materials like hardwood with efficiency. This power is complemented by a quality chain bar, typically measuring 18 inches in length, providing the right length for a variety of cutting tasks.

One of the key technologies in the Poulan 222 is its Easy Start feature. This innovative system significantly reduces the amount of effort needed to pull the starter rope, making it easier to start the saw with less physical exertion. Additionally, the chain saw incorporates a primer bulb that ensures fuel reaches the engine quickly, further aiding in starting.

The Poulan 222 is designed with user safety and comfort in mind. It features an inertia-activated chain brake that helps prevent accidents in case of kickback, a common hazard when operating a chain saw. The ergonomic handle and anti-vibration technology contribute to a more comfortable grip, reducing strain during prolonged use.

Another noteworthy characteristic of the Poulan 222 is its fuel efficiency. The engine is designed to consume less fuel while providing high performance, leading to fewer stops for refueling and increased productivity during work sessions.

Overall, the Poulan 222 is a well-rounded chain saw that combines power, comfort, and advanced features. Whether tackling home improvement projects, maintaining a landscape, or executing professional tree work, the Poulan 222 stands out as a reliable and efficient tool. It represents a smart investment for anyone looking to enhance their cutting capabilities with a saw that delivers both power and precision.
Top Page Image Contents