Poulan 222 instruction manual Need ASSISTANCE?, Storage, Need Service PART?, Trouble Cause Remedy

Page 16

STORAGE

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric mo- tors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of chil- dren.

SBefore storing, drain all fuel from the unit. Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an

open flame from hot water heaters, electric motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

TROUBLESHOOTING TABLE

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

NEED ASSISTANCE?

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your dealer or place of purchase.

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

 

TROUBLE

CAUSE

REMEDY

 

 

 

 

 

 

 

Engine will not

1. Ignition switch off.

1.

Move ignition switch to ON.

 

start or will run

2. Engine flooded.

2.

See “Difficult Starting” in

 

only a few

 

 

 

Operation Section.

 

seconds after

3. Fuel tank empty.

3.

Fill tank with correct fuel mixture.

 

starting.

4. Spark plug not firing.

4.

Install new spark plug.

 

 

5. Fuel not reaching

5.

Check for dirty fuel filter; replace.

 

 

 

carburetor.

 

Check for kinked or split fuel line;

 

 

 

 

 

repair or replace.

 

 

 

 

 

 

 

Engine will

1.

Idle speed requires

1. See “Carburetor Adjustment” in the

 

not idle

 

adjustment.

 

Service and Adjustments Section.

 

properly.

2.

Carburetor requires

2. Contact an authorized service dealer.

 

 

 

adjustment.

 

 

 

 

Engine will not

1.

Air filter dirty.

1. Clean or replace air filter.

 

accelerate,

2.

Spark plug fouled.

2. Clean or replace plug and regap.

 

lacks power,

3.

Chain brake engaged.

3. Disengage chain brake.

 

or dies under

4.

Carburetor requires

4. Contact an authorized service dealer.

 

a load.

 

adjustment.

 

 

 

 

 

 

 

 

 

 

 

Engine

1.

Too much oil mixed with

1.

Empty fuel tank and refill with

 

smokes

 

gasoline.

 

correct fuel mixture.

 

excessively.

 

 

 

 

 

 

Chain moves

1. Idle speed requires

1. See “Carburetor Adjustment” in the

 

at idle speed.

 

adjustment.

 

Service and Adjustments Section.

 

 

2. Clutch requires repair.

2.

Contact an authorized service dealer.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual de Instrucciones Manuel d’Instructions English Español FrançaisSafety Rules Identification of SymbolsPlan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Chain Brake and CKA Angle Front Hand Guard, designed to reduceBack toward the operator LengthAssembly Attaching the BAR & Chain If notChain Brake Nuts Mount the BarChain Tension Including units with chain already installed Adjusting the tensionChecking the tension CuttersON/STOP Switch Know Your Chain SAWThrottle Trigger Throttle LOCK-OUTStarting Fueling EngineBAR and Chain Lubrication Important Points to RememberStarting a Warm Engine Cutting MethodsImportant Points Tree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Direction of FallBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportService Limbing and Pruning Important PointsLimbing PruningCleaning the air filter Cleaning the Spark ARREST- ING ScreenAIR Filter Inspect Muffler and Spark Arresting ScreenCarburetor Adjustment BAR MaintenanceChain Sharpening Ignition TimingNeed Service PART? Need ASSISTANCE?Storage Need ASSISTANCE?Limited Warranty Tions The U.S. Environmental ProtectionPlacement and Repair of Emission

222 specifications

The Poulan 222 is a versatile and powerful chain saw designed to meet the demands of both casual users and professionals alike. Renowned for its reliability and performance, the Poulan 222 is an excellent addition to the toolkits of landscapers, tree surgeons, and homeowners who require a dependable cutting tool for various tasks.

One of the standout features of the Poulan 222 is its lightweight design. Weighing in at just under 11 pounds, this chain saw is easy to maneuver, allowing users to work for extended periods without excessive fatigue. The balanced weight distribution also contributes to stability during operation, enhancing precision cuts.

The Poulan 222 is powered by a robust 2-cycle engine, delivering exceptional cutting power for both light and heavy-duty applications. With a displacement of 45cc, this engine is capable of producing up to 2.0 horsepower, which means it can handle tough materials like hardwood with efficiency. This power is complemented by a quality chain bar, typically measuring 18 inches in length, providing the right length for a variety of cutting tasks.

One of the key technologies in the Poulan 222 is its Easy Start feature. This innovative system significantly reduces the amount of effort needed to pull the starter rope, making it easier to start the saw with less physical exertion. Additionally, the chain saw incorporates a primer bulb that ensures fuel reaches the engine quickly, further aiding in starting.

The Poulan 222 is designed with user safety and comfort in mind. It features an inertia-activated chain brake that helps prevent accidents in case of kickback, a common hazard when operating a chain saw. The ergonomic handle and anti-vibration technology contribute to a more comfortable grip, reducing strain during prolonged use.

Another noteworthy characteristic of the Poulan 222 is its fuel efficiency. The engine is designed to consume less fuel while providing high performance, leading to fewer stops for refueling and increased productivity during work sessions.

Overall, the Poulan 222 is a well-rounded chain saw that combines power, comfort, and advanced features. Whether tackling home improvement projects, maintaining a landscape, or executing professional tree work, the Poulan 222 stands out as a reliable and efficient tool. It represents a smart investment for anyone looking to enhance their cutting capabilities with a saw that delivers both power and precision.
Top Page Image Contents