Poulan 115156526 instruction manual Important Points to Remember, Starting a Warm Engine

Page 10

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

WARNING: Do not attempt to throw or drop--start the chain saw. Doing so will put the operator at risk of serious injury due to loss of control of the chain saw.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle If your hand slips off the front handlebarAssembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Primer Bulb Throttle LOCK-OUTCHOKE/FAST Idle Lever Chain BrakeStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Operating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingService Check Guide BAR Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelReplace Spark Plug Cleaning the Spark ARREST- ING ScreenChain Adjustment To Sharpen ChainCooling System Carburetor AdjustmentIdle Speed-T RightFuel System StorageSeasonal Storage EngineLoad Adjustment Engine Empty fuel tank and refill withPoulan PRO Ligations The U.S. Environmental

115156526 specifications

The Poulan 115156526 is a versatile chainsaw designed for both casual users and more experienced operators. This model is particularly noted for its blend of power, efficiency, and user-friendly features, making it a popular choice for tasks ranging from trimming branches to cutting firewood.

One of the standout features of the Poulan 115156526 is its robust engine. Equipped with a 42cc, two-stroke engine, it provides ample power for tackling a variety of cutting jobs. This engine delivers a high power-to-weight ratio, ensuring that users can handle the tool with ease without compromising on performance. The chainsaw’s design emphasizes not only power but also fuel efficiency, allowing users to work longer without frequent refueling.

The bar length of the 115156526 typically measures around 16 inches, which strikes a balance between maneuverability and cutting capacity. This length is ideal for medium-sized trees and shrubs, making it a great tool for yard maintenance and landscaping tasks. Additionally, the chainsaw features a low-kickback chain, which enhances safety while providing smooth and efficient cutting.

Another notable aspect of the Poulan 115156526 is its starting technology. Equipped with an easier starting mechanism, this chainsaw often incorporates features such as an automatic primer bulb and easy-to-use recoil starter, making it simpler to start even for novice users. The anti-vibration system minimizes user fatigue during operation, allowing for prolonged use without discomfort.

Safety features are also critical for any chainsaw, and the Poulan 115156526 does not disappoint. The chainsaw includes a chain brake designed to stop the chain almost instantaneously in case of kickback. This feature is crucial for novice users who may not yet be fully accustomed to handling chainsaws.

In terms of maintenance, the Poulan 115156526 is designed for ease of access to the air filter and spark plug, making routine upkeep more straightforward. Its removable side access chain tensioner allows for quick and hassle-free adjustments to the chain tension, which is vital for consistent cutting performance.

Overall, the Poulan 115156526 stands out for its combination of power, safety, and user-friendly innovation. Whether you are clearing your yard, maintaining trees, or preparing firewood, this chainsaw provides the reliability and efficiency needed to get the job done effectively.
Top Page Image Contents