Poulan 115156526 Braking function control Caution The chain brake must be, Operating Tips

Page 11

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an authorized ser- vice dealer. Take your unit to the place of pur- chase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

OPERATING TIPS

SCheck chain tension before first use, after 1 minute of operation, and each time be-

fore you start the chain saw. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary. If the chain jumps off the guide bar, inspect the chain for damaged drive links before reinstalling. Burrs on drive links, which prevent them from entering the groove of the guide bar,

can be removed with a flat file.

SKeep the chain out of dirt and sand. Even a small amount of dirt will dull a chain, increase the possibility of kickback, and require chain sharpening or replacement.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unneces- sary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for lon- ger than 30 seconds at full throttle.

S To avoid losing control when cut is com- plete, do not put pressure on saw at end

of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near buildings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified immediately.

SCarefully plan your sawing operation in ad- vance.

SClear the work area. You need a clear area

all around the tree so you can have secure footing.

SThe chain saw operator should keep on the uphill side of the terrain as the tree is

likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause the tree to fall in a particular direction.

Natural conditions that can cause a tree to fall in a particular direction include:

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual de Instrucciones Manuel d’Instructions Tions found in this manual Starting ReminderPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Reduce the Chance of KickbackMaintain Control Avoid Pinch-KickbackIf your hand slips off the front handlebar Kickback Safety FeaturesChain Brake and CKA Angle Chain saws as set by Ansi B175.1Attaching the BAR & Chain If not AssemblyChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation Chain Brake Throttle LOCK-OUTCHOKE/FAST Idle Lever Primer BulbDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Tree Felling Techniques Braking function control Caution The chain brake must beInertia activating function control Operating TipsImportant Points Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Check Guide BARTo Sharpen Chain Cleaning the Spark ARREST- ING ScreenChain Adjustment Replace Spark PlugRight Carburetor AdjustmentIdle Speed-T Cooling SystemEngine StorageSeasonal Storage Fuel SystemEmpty fuel tank and refill with Load Adjustment EngineLigations The U.S. Environmental Poulan PRO

115156526 specifications

The Poulan 115156526 is a versatile chainsaw designed for both casual users and more experienced operators. This model is particularly noted for its blend of power, efficiency, and user-friendly features, making it a popular choice for tasks ranging from trimming branches to cutting firewood.

One of the standout features of the Poulan 115156526 is its robust engine. Equipped with a 42cc, two-stroke engine, it provides ample power for tackling a variety of cutting jobs. This engine delivers a high power-to-weight ratio, ensuring that users can handle the tool with ease without compromising on performance. The chainsaw’s design emphasizes not only power but also fuel efficiency, allowing users to work longer without frequent refueling.

The bar length of the 115156526 typically measures around 16 inches, which strikes a balance between maneuverability and cutting capacity. This length is ideal for medium-sized trees and shrubs, making it a great tool for yard maintenance and landscaping tasks. Additionally, the chainsaw features a low-kickback chain, which enhances safety while providing smooth and efficient cutting.

Another notable aspect of the Poulan 115156526 is its starting technology. Equipped with an easier starting mechanism, this chainsaw often incorporates features such as an automatic primer bulb and easy-to-use recoil starter, making it simpler to start even for novice users. The anti-vibration system minimizes user fatigue during operation, allowing for prolonged use without discomfort.

Safety features are also critical for any chainsaw, and the Poulan 115156526 does not disappoint. The chainsaw includes a chain brake designed to stop the chain almost instantaneously in case of kickback. This feature is crucial for novice users who may not yet be fully accustomed to handling chainsaws.

In terms of maintenance, the Poulan 115156526 is designed for ease of access to the air filter and spark plug, making routine upkeep more straightforward. Its removable side access chain tensioner allows for quick and hassle-free adjustments to the chain tension, which is vital for consistent cutting performance.

Overall, the Poulan 115156526 stands out for its combination of power, safety, and user-friendly innovation. Whether you are clearing your yard, maintaining trees, or preparing firewood, this chainsaw provides the reliability and efficiency needed to get the job done effectively.
Top Page Image Contents