Poulan 115156526 instruction manual Service

Page 14

SLeave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and limbs.

Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

S Remove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and free- ly hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your first cut 1/3 of the way through the bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch (2.5 to 5 cm) collar from the truck of the tree.

Second cut

Third cut

Collar

First cut

Pruning technique

SERVICE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec- ommended maintenance described in the instruction manual performed by an authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, Poulan PRO may not pay for repairs under warranty. It is your re- sponsibility to maintain and perform general maintenance.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . . Before each use For damaged parts . . . Before each use For loose caps . . . . . . Before each use For loose fasteners . . . Before each use For loose parts . . . . . . Before each use

Inspect and Clean:

Bar . . . . . . . . . . . . . . . . Before each use Complete saw . . . . . . . After each use Air filter . . . . . . . . . . . . . Every 5 hours* Chain brake . . . . . . . . . Every 5 hours* Spark arresting screen

and muffler . . . . . . . . . . Every 25 hours* Replace spark plug . Yearly Replace fuel filter . . . Yearly

*Hours of Operation --

Each hour of operation is approximately 2 tanks of fuel.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain unit as instructed in this manual. Various adjustments will need to be made periodical- ly to properly maintain your unit.

SOnce a year, replace the spark plug, air filter, and check guide bar and chain for wear. A new spark plug and air filter assures proper air-fuel mixture and helps your engine run better and last longer.

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

NOTE: It is normal for a small amount of oil to appear under the saw after engine stops. Do not confuse this with a leaking oil tank.

S ON/STOP Switch -- Ensure ON/STOP switch functions properly by moving the switch to the STOP position. Make sure en- gine stops; then restart engine and continue.

S Fuel Tank -- Do not use saw if fuel tank shows signs of damage or leaks.

SOil Tank -- Do not use saw if oil tank shows signs of damage or leaks.

CHECK FOR LOOSE

FASTENERS AND PARTS

SBar Nuts S Chain

S Muffler

S Cylinder Shield S Air Filter

S Handle Screws S Vibration Mounts S Starter Housing S Front Hand Guard

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull chain makes a sawdust powder and cuts slowly. See CHAIN SHARPENING.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Manual de Instrucciones Manuel d’Instructions Tions found in this manual Starting ReminderPlan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle If your hand slips off the front handlebarAssembly Attaching the BAR & Chain If notChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation Primer Bulb Throttle LOCK-OUTCHOKE/FAST Idle Lever Chain BrakeDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Operating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingService Check Guide BAR Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelReplace Spark Plug Cleaning the Spark ARREST- ING ScreenChain Adjustment To Sharpen ChainCooling System Carburetor AdjustmentIdle Speed-T RightFuel System StorageSeasonal Storage EngineLoad Adjustment Engine Empty fuel tank and refill withPoulan PRO Ligations The U.S. Environmental

115156526 specifications

The Poulan 115156526 is a versatile chainsaw designed for both casual users and more experienced operators. This model is particularly noted for its blend of power, efficiency, and user-friendly features, making it a popular choice for tasks ranging from trimming branches to cutting firewood.

One of the standout features of the Poulan 115156526 is its robust engine. Equipped with a 42cc, two-stroke engine, it provides ample power for tackling a variety of cutting jobs. This engine delivers a high power-to-weight ratio, ensuring that users can handle the tool with ease without compromising on performance. The chainsaw’s design emphasizes not only power but also fuel efficiency, allowing users to work longer without frequent refueling.

The bar length of the 115156526 typically measures around 16 inches, which strikes a balance between maneuverability and cutting capacity. This length is ideal for medium-sized trees and shrubs, making it a great tool for yard maintenance and landscaping tasks. Additionally, the chainsaw features a low-kickback chain, which enhances safety while providing smooth and efficient cutting.

Another notable aspect of the Poulan 115156526 is its starting technology. Equipped with an easier starting mechanism, this chainsaw often incorporates features such as an automatic primer bulb and easy-to-use recoil starter, making it simpler to start even for novice users. The anti-vibration system minimizes user fatigue during operation, allowing for prolonged use without discomfort.

Safety features are also critical for any chainsaw, and the Poulan 115156526 does not disappoint. The chainsaw includes a chain brake designed to stop the chain almost instantaneously in case of kickback. This feature is crucial for novice users who may not yet be fully accustomed to handling chainsaws.

In terms of maintenance, the Poulan 115156526 is designed for ease of access to the air filter and spark plug, making routine upkeep more straightforward. Its removable side access chain tensioner allows for quick and hassle-free adjustments to the chain tension, which is vital for consistent cutting performance.

Overall, the Poulan 115156526 stands out for its combination of power, safety, and user-friendly innovation. Whether you are clearing your yard, maintaining trees, or preparing firewood, this chainsaw provides the reliability and efficiency needed to get the job done effectively.
Top Page Image Contents