Poulan 545137280 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Cold Engine

Page 11

Genuine Poulan or Poulan PRO bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PRO oil resists high temperature thinning. If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil.

S Never use waste oil for bar and chain lubrication.

S Always stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before stor- age for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. See the STORAGE sec- tion for additional information.

HOW TO STOP YOUR UNIT

S To stop the engine, move the ON/OFF switch to the OFF position.

ON/OFF Switch

HOW TO START YOUR UNIT

WARNING: Make sure the chain will not make contact with any object while starting the engine. Never try to start the unit when the guide bar is in a cut. Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move the start lever to the START posi- tion.

Starter Handle

Start

Lever

Primer Bulb

Muffler

5.Pull starter rope handle sharply until en- gine starts and runs.

6.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1. Move ON/OFF switch to the ON position.

2. Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

3. Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL: Edger . . . . . . . . . . . . . . . . . . . . . . . PP1000E Cultivator . . . . . . . . . . . . . . . . . . . . PP2000T Blower . . . . . . . . . . . . . . . . . . . . . . PP3000B Brushcutter . . . . . . . . . . . . . . . . . . PP4000C

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING PRUNER ATTACH- MENT, LINE TRIMMER ATTACH-

MENT, OR OTHER OPTIONAL AT- TACHMENTS

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for

stability.

1.Loosen the coupler by turning the knob counterclockwise.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PP446ET Plan Ahead Identification of SymbolsSafety Rules Pruner SafetyLine Trimmer Safety Reduce the Chance Kickback Maintain Your Unit in Good Working OrderHandle Fuel with Caution KickbackTion of this tool Kickback Safety FeaturesMaintain Control For Optional AttachmentsAlways use the handlebar when using edg- er attachment Edger SafetyBLOWER/VACUUM Safety Brushcutter SafetyCurs, stop the engine and inspect the unit for damage Cultivator SafetyHedge Trimmer Safety Snow Thrower SafetyTools Required AssemblyShoulder Strap Assembly Attaching Shield for Line Trimmer Attachment Adjusting the Assist HandleTo Relocate Shoulder Strap Clamp Operation Starting a Warm Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Cold EngineUpper Shaft Coupler Installing Attachment HangerInstalling Optional ATTACH- Ments Trimmer Line Advance Pruning Important PointsPruning Technique Cutting Methods Maintenance Service and Adjustments Replacing the Line Chain AdjustmentTo Replace Chain Fuel System Carburetor AdjustmentIdle Speed Adjustment Seasonal StorageCarbon build-up on Troubleshooting Table Cause RemedyLoad Adjustment Compression lowIs Covered Repair or Replace Limited WarrantyIntermediate 125 hours Extended 300 hours

545137280 specifications

The Poulan 545137280 is a versatile and powerful gas-powered chainsaw designed to meet the needs of both professionals and avid DIY enthusiasts. Renowned for its durability and efficiency, this chainsaw stands out in the crowded market due to its advanced technologies and ergonomic design.

One of the prominent features of the Poulan 545137280 is its 50cc, 2-stroke engine, which delivers a robust performance, making it ideal for cutting through heavy hardwoods and tackling demanding jobs. This engine not only provides ample power but also ensures that the chainsaw operates smoothly, resulting in less vibration for the user, which enhances comfort during extended use.

The chainsaw is equipped with a 20-inch bar and chain, providing an ideal length for a variety of cutting tasks, from felling trees to trimming branches. The larger bar allows users to cover more ground with each cut, thus increasing efficiency. The sharp chain is designed for optimum performance and quick cutting, ensuring cleaner finishes and reduced kickback for safer operation.

Another standout feature is Poulan’s patented Easy Start technology. This technology significantly reduces starting effort, allowing users to start the chainsaw with minimal effort, even in cold weather. Combined with the choke lever and primer bulb, this system ensures that the chainsaw is ready to go with just a few pulls, minimizing downtime before tackling the next cutting task.

In terms of safety, the Poulan 545137280 incorporates a chain brake system that automatically stops the chain if a kickback is detected, reducing the risk of accidents. The rear handle is ergonomically designed to provide a comfortable grip, allowing for better control during operation. Additionally, the lightweight design of the chainsaw helps reduce user fatigue, making it suitable for prolonged use.

Maintenance is made simple with the tool-less chain tensioning feature that enables users to adjust the chain tension without the need for additional tools. This not only saves time but also ensures that the chainsaw remains in optimal working condition without unnecessary hassle.

In summary, the Poulan 545137280 chainsaw combines power, efficiency, and user-friendly features that cater to both professionals and hobbyists. Its advanced technologies, including the powerful engine, Easy Start system, and enhanced safety features, make it a reliable tool for a variety of cutting tasks. Whether for yard maintenance or professional logging jobs, the Poulan 545137280 proves to be a valuable addition to any toolkit.
Top Page Image Contents