RIDGID RD80763 Assembling the trigger handle, Attaching the auxiliary handle, Trigger Handle

Page 11

ASSEMBLY

WARNING:

Make sure the nozzle and hose connections are secure before starting the machine. A non-secured accessory could become a projectile if not properly installed which could result in serious injury.

assembling the trigger handle

See Figure 7.

TRIGGER

HANDLE auxiliary

HANDLE

nPlace the threaded end of the spray wand in the connec- tor on the end of the trigger handle.

nTurn the connector clockwise until it stops. This secures the wand in place.

nWhen not in use, remove the spray wand from the trigger handle by turning the connector counterclockwise. Store the unassembled spray wand in the spray wand storage area.

attaching the auxiliary handle

See Figure 7.

n Place the threaded stud on the end of the auxiliary handle

into the hole in the trigger handle as shown below. Turn

clockwise to tighten.

CONNECTOR

high

PRESSURE HOSE

SPRAY

WAND

Fig. 7

NOTE: You can install the handle on either the left or right

side of the spray wand, depending on operator prefer-

ence. The handle must always be used to prevent loss

of control and possible serious injury.

n To switch sides, loosen the auxiliary handle and rotate to

the opposite side. Tighten securely before use.

connecting high pressure hose to

TRIGGER HANDLE

See Figure 8.

nPull back and hold the collar on the high pressure hose. In- sert the inlet coupler on the trigger handle into the collar.

nRelease the collar and push until it locks into place.Pull on the hose to be certain it is properly secured.

attaching INJECTION hose

See Figure 9.

Before detergent can be used with this machine, the injection hose must be attached.

nPush the open end of the clear injection hose securely over the fitting as shown in figure 9.

nPlace the filtered end of the injection hose in the bottle of detergent.

COLLAR

inlet

 

coupler

Fig. 8

Injection hose

Fig. 9

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents RD80763/RD80964 OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions Important Safety InstructionsSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceRecoil FeaturesProduct Specifications Max. rating determined by Pwma StandardAssembly Washer wheel hitch pin Attaching the rear panelHandle Torx Screw Rear panel AxleRaising and Lowering the handle Attaching the wheel assemblySupport Foot Attaching the trigger handle restTrigger Handle Connecting high pressure hose toAssembling the trigger handle Attaching the auxiliary handleOIL CAP /  Dipstick Funnel Adding oil to the engineAdding gasoline to the Fuel tank FunnelTo connect the garden hose to the machine Connecting the garden hose to the pressure washerConnecting the high pressure hose to the pump OperationSee Figures 14 Engine SwitchApplications Starting and stopping the pressure washerSee Using the spray wand triggerUsing the Nozzles OperationSee Figures 20 Washing with detergentMoving the pressure washer Rinsing with the pressure washerAIR Filter Cover MaintenanceGeneral Maintenance Cleaning the air filterChecking a fouled spark plug Nozzle maintenanceChanging the OIL Preparing for use after storage Pump maintenanceStoring the pressure washer Problem Cause Solution TroubleshootingPage Federal Emissions Component Defect Warranty WarrantyGeneral Emissions Warranty Coverage High Altitude Engine Operation Rely on Subaru Robin Reliability Limited 3 Year Engine Warranty for Ridgid Pressure WasherLimited Manufacturer’s Warranty from Subaru Robin Warranty PeriodsHOW to Obtain Service Ridgid Pressure Washer 3 Year Limited WarrantyWhat is Covered Under the 3 Year Limited Warranty What is not CoveredModel No RD80763 / RD80964 Serial No Customer Service InformationRD80763 / RD80964
Top Page Image Contents