Scag Power Equipment SFW36-16BV Drive Control Adjustments, Belt Adjustment, Belt Alignment

Page 23

Section 6

R

ADJUSTMENTS

6.1 DRIVE CONTROL ADJUSTMENTS

1.Adjust the steering control rods so that there is approximately 3/4" clearance from the bottom of the rod to the bottom of the neutral latch slot when in the drive position. See Figure 6-1.

2.Adjust the steering brake rods so that the brakes do not apply until the steering levers are pulled tight to the handles. When the steering levers are locked in the neutral position the machine should move freely.

Neutral

Latch

Neutral Lock

Position

Drive Position

3/4"

Steering

Brake Lever

SC404GB05

Figure 6-1. Steering Control Rod Adjustment

- NOTE -

Operator pressence lever removed for clarity. Never operate equipment with the interlock system disconnected.

6.2Throttle Control and Choke Adjustments

These adjustments must be performed by your Scag dealer to ensure proper and efficient running of the engine. Should either need adjustment, contact your authorized Scag service center.

6.3 BELT ADJUSTMENT

WARNING

Before removing any guards, shut the engine off and remove the ignition key.

All drive belts are spring loaded and self-tensioning, however after the first 2, 4, 8 and 10 hours of operation, the belts should be checked for proper alignment and wear. Thereafter, check the belts after every 40 hours of operation or weekly, whichever occurs first.

6.4 BELT ALIGNMENT

Belt alignment is important for proper performance of your Scag mower. If you experience frequent belt wear or breakage, see your authorized Scag service center for belt adjustment.

6.5 CUTTER DECK ADJUSTMENTS

Cutter deck level, pitch and height are set at the factory. However, if these adjustments should ever need to be made, the following procedures will aid in obtaining the proper cutter deck adjustment.

- NOTE -

Before proceeding with the cutter deck adjustments, be sure that all tires are properly inflated.

Cutter Deck Level

The cutter deck should be level from side-to-side for proper cutting performance. To check for level, be sure that the mower is on a flat, level surface, the tires are properly inflated and the cutter deck is set at the most common cutting height that you will use. On the RH side of the machine, check the distance from the top of the cutter deck to the floor. Next check the distance from the top of the cutter deck to the floor on the LH side of the machine. Both measurements should be the same. If the two measurements are different, the cutter deck level must be adjusted as follows:

19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OPERATOR’S Manual Always Follow Osha Approved Operation Remember Your Mower is only AS Safe AS the OperatorTable of Contents Inside Back Cover Limited Warranty SFWServicing The Engine And Drive Train Components General InformationIntroduction Direction ReferenceSTT Models SymbolsSignal Word Safety InformationSignal Words This symbol means Attention! Become Alert! YourOperation Considerations Maintenance Considerations & storage Using a spark arrestor Riding Attachments Safety and Instructional DecalsInstall Belt COvER Before Falling HAzARD USE only Scag APPROvEDEngine Deck SpecificationsEngine ElectricalProductivity Weights and DimensionsControls and Instrument Identification Operating InstructionsFirst Day of Use or Approximately 20 Hours Safety Interlock SystemInitial RUN-IN Procedures Starting the EngineReverse Travel Ground Travel and SteeringForward Travel Parking the Mower Engaging the Deck Drive Cutter Hillside Operation BladesMoving Mower with Engine Stopped Rotating BladesAfter Operation Removing Clogged MaterialCutting Height Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Cutting path Scalping Blades HittingDirt or CuttingVery Close To the Ground Step Cut Ridge in CenterCutter Deck Adjustments AdjustmentsDrive Control Adjustments Belt AdjustmentCutter Deck Pitch Electric clutch adjustmentIf the air gap is too narrow, the clutch armature may drag Procedure Comments Break-In 100 200 500 First MaintenanceMaintenance Chart Recommended Service Intervals Lubrication Maintenance Chart Recommended Service Intervals ContdEngine Fuel System Engine OilCutter Blades Engine Air CleanerDrive Belts Blade Sharpening Blade ReplacementTires Scag Approved Attachments and Accessories Illustrated Parts ListCutter Deck 462150 Cutter Deck Weldment w/Decals 14 20 1217 462149 Cutter Deck Weldment w/Decals Cutter Deck Controls Cutter Deck Controls Handle Assembly Pulley, Jackshaft 3.25 OD x .625 Bore Engine Deck Description Electrical System and Throttle Control Ref. No Description Do not Operate Unless Grass CATCHER, Mulching kIT or Replacement Decals and Information PlatesSpinning Blades Rotating Blades and Belts1 2 3 SFW Electrical Schematic Limited Warranty SFW
Related manuals
Manual 18 pages 62.01 Kb

SFW36-16BV specifications

Scag Power Equipment is renowned for its robust and innovative lawn care machinery, with the SFW36-16BV standing out as a prime example of their commitment to quality and performance. This versatile walk-behind mower is designed to make yard maintenance efficient and effective for both residential and commercial users.

One of the main features of the SFW36-16BV is its powerful 16-horsepower Vanguard engine. This reliable engine provides ample power to tackle tough grass and uneven terrain, ensuring a clean and precise cut every time. The engine is also designed for longevity, featuring improved air filtration and easy-access oil drain for hassle-free maintenance.

The mower's 36-inch cutting deck is crafted from durable steel, allowing it to withstand the rigors of regular use in various conditions. The deck height can be easily adjusted, offering a range of cutting options to accommodate different grass types and seasonal growth patterns. This feature makes the SFW36-16BV ideal for homeowners with diverse landscaping needs or lawn care professionals seeking adaptability.

A standout characteristic of the SFW36-16BV is its intuitive operation system. The unit is equipped with a friction disc drive that provides smooth control while navigating tight spaces. Operators appreciate the precise maneuverability, particularly in complex landscapes or crowded yards. The mower's low center of gravity enhances stability, making it easy to handle on slopes and inclines.

Safety is a priority in the design of the SFW36-16BV, which features a comprehensive safety system including a dual-lever operation for instant stopping. This provides peace of mind during operation, especially in busy or populated areas. Additionally, the ergonomic handle offers comfort during extended use, reducing fatigue.

In terms of technology, Scag ensures that the SFW36-16BV is equipped with features that enhance the mowing experience. The easy-to-use height adjustment lever and simple-to-access control panel make this mower user-friendly. This encapsulates Scag's focus on crafting equipment that meets the needs of lawn care professionals as well as amateurs.

Overall, the Scag SFW36-16BV walk-behind mower offers a blend of power, durability, and user-friendly features, making it a reliable choice for those seeking efficient lawn care solutions. Its outstanding engineering and thoughtful design ensure that it stands out in a competitive market, catering to a wide array of mowing demands. Whether for commercial purposes or residential lawns, the SFW36-16BV delivers performance and satisfaction that lawn care enthusiasts can count on.
Top Page Image Contents